A wide flange steel beam shown supports a permanent concrete masonry wall, floor slab, architectural finishes, mechanical and electrical systems. Determine the uniform dead load in kips per linear foot acting on the beam. The wall is 9.5-ft high, non-load bearing and laterally braced at the top to upper floor framing (not shown). The wall consists of 8-in. lightweight reinforced concrete masonry units with an average weight of 90 psf. The composite concrete floor slab construction spans over simply supported steel beams, with a tributary width of 10 ft, and weighs 50 psf. The estimated uniform dead load for structural steel framing, fireproofing, architectural features, floor finish, and ceiling tiles equals 24 psf, and for mechanical ducting, piping, and electrical systems equals 6 psf. FINAL ANSWER mechanical duct 9.5 MZAUPAN BANDANGAY 8 concrete masonry partition -concrete floor slab piping wide flange steel beam with fireproofing ceiling tile and suspension hangers Section

A wide flange steel beam shown supports a permanent concrete masonry wall, floor slab, architectural finishes, mechanical and electrical systems. Determine the uniform dead load in kips per linear foot acting on the beam. The wall is 9.5-ft high, non-load bearing and laterally braced at the top to upper floor framing (not shown). The wall consists of 8-in. lightweight reinforced concrete masonry units with an average weight of 90 psf. The composite concrete floor slab construction spans over simply supported steel beams, with a tributary width of 10 ft, and weighs 50 psf. The estimated uniform dead load for structural steel framing, fireproofing, architectural features, floor finish, and ceiling tiles equals 24 psf, and for mechanical ducting, piping, and electrical systems equals 6 psf. FINAL ANSWER mechanical duct 9.5 MZAUPAN BANDANGAY 8 concrete masonry partition -concrete floor slab piping wide flange steel beam with fireproofing ceiling tile and suspension hangers Section

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Equation of flow What is the difference between Lagrangian and Eulerian approach in writing equation of water flow? Can turbulent flow be steady? Justify briefly your answer
NOTE MY ID NUMBER 20-3994-175 ANSWER NUMBER 8 9 10 11 12 - Don’t round off answers unless it is already the final answer. -Final answers must be up to 3 decimal places only. PLEASE INDICATE THE NUMBER IN EVERY ANSWER.
Slove the following equation using grammars rule: X + 2y + Z = 3 2X + y - Z = 0 X - y + Z = 0
What is the difference in meaning between the following verbs? Moke them in sentences: Evaluate - Asses Compute-Calculate Derive -Infer Approximate -Estimate Discover-Find
• Write your answer to the blank field in this format: xXXX.Xx (e.g., 2004.32) • Use dot (.) as the decimal separator • Use only two decimal places after the decimal separator. • Use grad unit for angles. • Do not add "m" or "meter" at the end of your answer. Find the sum of the coordinates (Y+X) of point "D" on a line linking N11 and N29, whose coordinates are given. Use intermediate point calculation method. X(m) PN Y(m) 2525.58 2004.32 N11 2598.44 N29 2075.34 N 101.79 oi 72.58 C46.96 Bộ32.74 P17.34 0.00 N11
Can you upload the solution? I cannot understand the process through text. Ty
The solutions and answers should have minimum of 3 decimals for linear measurements and should be in Degree-Minute-Seconds (2 decimals for seconds) for angular measurement, if not whole number. An engineer is tasked to measure a whole line multiple time. Since the length of the line is significantly longer than the steel tape, the engineer decided to measure the line in three segments. First, the engineer measures a 50m known line using the steel tape and find out that the tape is too long with the observation having only 49.2m. With these values, the correction factor of ???? = 50? − 49.2?. After determining such corrections for future calibration, the engineer measured each segments. The following are the observations: 1st Segment: 46.2m, 46.3m, 46.5m; 2nd Segment: 48.3m, 48.2m, 48.1m; 3rd Segment: 32.3m, 32.6m, 32.4m. Determine the complete expression of the most probable value (together with probable error) of the line.
I need help with parts A,B, and C. The learning goal starts in the first screenshot and continues on the second one.
Subject: Fluid Mechanics II Question: Where is manning’s coefficient used? Sir, please answer briefly and according to topic
The students usually write their laboratory report together. What is the technical problem of this sentence? Select one: o a. redundancy b. prepositional phrases c. passive voice d. multisyllabic
State the objective of the analysis in a short sentence.