An interior column supports only loads from the second floor of an office building. The tributary area to the column is 240 ft², and the dead load is 35 psf. Find: a. Basic floor live load L, in psf b. Reduced floor live load L in psf c. Total load to column in k

An interior column supports only loads from the second floor of an office building. The tributary area to the column is 240 ft², and the dead load is 35 psf. Find: a. Basic floor live load L, in psf b. Reduced floor live load L in psf c. Total load to column in k

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: used in a transmission not restrained in directio N/mm?.

Q: A W1 L 3 B 13. 3 C mi L 333 W2 D (a) A 12m long beam ABCD is loaded as shown above and rests on…

A: P=500N L=12m To find load intensities w1 and w2

Q: A W1 را در 3 P ↓ B 3 2P C 3 W2 D ) A 12m long beam ABCD is loaded as shown above and rests on…

Q: A short rectangular column 300 mm on one side and 400 mm on the other side is reinforced with…

Q: esign a purlin section for the following data: -paullng of roof trusses c/c Dead load of roofing…

Q: 1- Design a rectangular section for the simply supported beam shown in the figure. The dead load wp…

Q: A typical rigid bar AB of the length 5m for a cantilever type car shed as shown in figure is hinged…

A: The given data is as follows: Length of bar AB=5 mDiameter of steel wires=3 cmDistance of wires from…

Q: column in the ground floor of a 5-story RC commercial building has an unfactored dead load of 401 kN…

Q: A short rectangular column 300 mm on one side and 400 mm on the other side. It is reinforced with…

Q: The compression member shown in Figure is pinned at both ends and supported in the weak direction at…

A: Compression members, the compressive loads tend to bend the member out of the plane of loading. They…

Q: Design the amount of reinforcement for a maximum positive moment in beam DEF. Present your answer in…

A: Given- A Reinforced concrete beams 300 mm wide and 500 mm deep are spaced 2.5 m on centers. The…

Q: An A-36 steel column has a length of 15 ft and is pinned at both ends. If the cross-sectional area…

A: To Determine Maximum axial load that can be applied before any type of failure of the column, P

Q: 6. Column ACB has a uniform rectangular cross section with b-20mm and d-25mm. The column is braced…

Q: A beam at right carries a uniform load w across its full length. Use this beam to respond to…

Q: Determine the maximum negative bending moments at point B due to a concentrated live loads of 50 kn…

Q: A stainless steel tube with an outside diameter of 66 mm and a wall thickness of 5 mm is used as a…

Q: Q1// An interior column in a braced frame has the following service load forces and moments causing…

A: Calculate the factored axial load on the column as follows: Pu=1.2wd+1.6wl Here, wd is the dead load…

Q: (a) A 12m long beam ABCD is loaded as shown above and rests on foundation material (soil) that…

A: Given :

Q: e loads and dead loads act in a

A: To find: We have to find whether the given statement is true or false. Given: Live loads and dead…

Q: An A36 W 12 x 65 column section is 8 m long, pinned at each end and has an additional support in the…

Q: Design the beam shown below for shear, it is subjected to a service live load of 40 KN/m and a…

Q: 2 kip/ft 6 in 10 in A B 16 in D. 40 kip 16 in 5 ft + 5ft - 10 ft- The simply-supported beam-column…

A: Given:- A beam is loaded with a uniform load and an axial load The intensity of the uniform load = 2…

Q: Floor System All question pertain to the following floor plan. The floor load is 60 Ib/ft?. Ignore…

Q: Consider pattern loading (skip loading) for live load (shown black on the sketch) for the simply…

Q: 1 Example 3 Design a simply supported rectangular reinforced beam with tension steel only to carry a…

A: Design is as per ACI CODE 318

Q: A cantilever beam of length L-6 ft supports a uniform load of intensity q-131 lb/ft and a…

A: GIVEN DATA LENGTH 6FT=1.8288m udl 131 lb/ft=0.177612 KN/m point load 1.884 lb=0.00838045 KN

Q: The structural system below using rotational spring + hinge support at joint A and rotational spring…

A: reestablishing force = applied second or force reestablishing force 'T1 = 2Kphi2 +Kphi1' applied…

Q: Question No. 12: (a) Explain the buckling of columns in detail. (b) Define factor of safety. Explain…

A: Buckling of Columns:Buckling of columns refers to the instability and failure of slender vertical…

Q: Solution por A and B?

A: (A) as per English unitsMaximum bending stress in beam is = 20.75 ksi (B) as pe metric unitsMaximum…

Q: Design a square tied column to support an unfactored axial dead load of 900kN and live load of 1240…

A: We need to design the column for the given specifications.

Q: For all problems, draw the indicated influence lines. For #1, use both the "unit load method" and…

Q: k What is the maximum uniform distributed load w- ft on a simply supported steel beam with size…

A: For calculating the maximum uniform load on the beam, we have to determine the value of the moment…

Q: A reinforced concrete column carries an axial dead load of 650 kN and an axial live load of 800 kN.…

A: The values given in the question are as follows Dead load(PD)=650 kN Live load(PL)=800 kN f'c=28 MPa…

Q: Solve for the total load at C

A: To determine the total force acting on C, calculate individual loads in C which are caused due by…

Q: I- 26 -I- 2 C 20 I 24 28 1 one story Building. WOL = 90 psf including beam self-weight. between D…

Q: A floor system of a 100 mm concrete slab supported by continuous T Beam and has bw = 350mm, bf = 950…

A: To find - Value of As2

Q: The 4-story building has a floor and roof dead load D = 70 psf, floor live load, L = 100 psf. The…

A: Given: The length of the slab 30 x 30 ft The magnitude of the dead Load, DL = 70 psf The magnitude…

Q: The uniformly distributed live load on the floor plan in Figure P2.9 is 100 lb/ft. Establish the…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: 18) A short rectangular column 300 mm on one side and 400 mm on the other side is reinforced with…

A: Given, b = 300 mm d = 400 mm φ = 20mm

Q: 1.The end moments of the beam shown due to service loads are tabulated below. Determine the design…

A: Dead loads, otherwise called long-lasting or static burdens, are those prevalent connected with the…

Q: The uniformly distributed live load on the floor plan in Figure P2.4 is 60 lb/ft2 . Establish the…

A: Solution

Q: mm on the other side is reinforced with 10-20-mm-diameter longitud

A: a short rectangular section of 300mm and 400mm built up with 10-20mm dia bar use f'c = 21 Mpa fy =…

Q: A 410-mm-diameter, non-slender, spiral column is symmetrically reinforced with 8-20 mm vertical…

A: Calculate design strength of column

Q: D+F D+H +F+L+T D+H+F+ (L, or R)

Q: A short rectangular column 300 mm on one side and 400 mm on the other side is reinforced with…

A: The given data is shown below: Column size=300×400Reinforcement=10-20mm diameterfc=21 MPafy=420…

Q: The total average load is 60 lbs/ft³. Calculate the reactions in Beam D Column 1| Beam A Column 2…

A: Given: Average dead load and live load = 60 psf

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Introduction and given data

VIEW

Step 2 Calculations

VIEW

Step 3 Final answer

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

USE NSCP2015
A 3m-LONG CANTILEVER BEAM IS CARRYING A UNIFORM DEADLOAD OF 20 kN/m (EXCLUDING SELFWEIGHT OF THE BEAM), AND A LIVE LOAD OF 15 kN/m. OTHER GIVEN: fc = 27.5 MPa fy = 414 MPa b = 300mm h = 600mm diameter of main reinforcements, db = 25mm diameter of transverse reinforcements, ds = 12mm use clear concrete cover of 45mm unit weight of concrete is 25kN/m3 Solve for the following: a. Reactions at the fixed support. b. Maximum FACTORED moment of the beam, Mu c. Effective depth of the beam d. As required e. No. of 25mm reinforcements required to resist Mu f. Spacing of stirrups at the critical location (d from face of the support) - use manual calculations, show your solutions.
Make correction to this exercice and explain in sentence or two why I made the mistake.
learn Determine the reaction forces for beams B-1, B-2, and B-3. Column A Column B Girder G-1 open Girder G-2 L1 L1 L1 • Live load = 30 psf • Dead load: (1) Slab = 50 psf, (2) Deck = 5 psf, (3) Mechanical equipment = 13 psf, (4) Suspended ceiling = 8 psf, (5) Beam = 25 Ib/ft, (6) Girder 35 lb/ft • Beam and Girder spacing: : (1) L1 = 14 ft, (2) L2 = 10 ft, (3) L3 = 10 ft Please round to the nearest one. Reaction force for Beam B-1 (one side only) = Ibs Reaction force for Beam B-2 (one side only) = Ibs Reaction force for Beam B-3 (open side) = Ibs Reaction force for Beam B-3 (Girder G-1 side) = Ibs MacBook Air II F8 F1 F2 F3 F4 F5 F6 F7 $ % & * 2 3 4 5 6 7 8 Beam B-1 Beam B-2 Beam B-3 Beam B-4 L3 L2
i need the answer quickly
Q.
hospren A column of size 200 x 300 mm has an effective length of 3 m and is reinforced with 6 nos. 20 mm dia. bars. Determine the safe load on the column using WSM. Use M 20 concrete and Fe 415 steel.
Question 17
Answer asap
Determine the bar forces of member BG. For the given loads: X= 26 kN, Y= 78 kN, Z= 104 kN, B= 26 Y G H. A m B C D E Y 4 @ 3B m = 12B m 6B m
For the flexible diaphragm below you are given x1 = 39, x2 = 28, y1 = 32, y2 = 20, and w1 = 2.0 (w2 is not necessary for this problem). Determine the maximum collector force. yi X₁ w₁ * x2+ W2 * Уг f
The floor system below is subjected to a uniformly distributed live load of 4.8 kN. The members are made of concrete that weighs 23.5 kN/m?. Required: The live load and dead load reactions for members GE-1, BI-1, and load on column CE-1. STRUCTURAL THEORY