A W1 L 3 B 13. 3 C mi L 333 W2 D (a) A 12m long beam ABCD is loaded as shown above and rests on foundation (soil) that exerts a linearly varying distributed load on the beam in response t loads. i). Draw the free body diagram for the beam ABCD and determine the magnitude of the load intensities w₁ and w₂ when P = 500 N.

A W1 L 3 B 13. 3 C mi L 333 W2 D (a) A 12m long beam ABCD is loaded as shown above and rests on foundation (soil) that exerts a linearly varying distributed load on the beam in response t loads. i). Draw the free body diagram for the beam ABCD and determine the magnitude of the load intensities w₁ and w₂ when P = 500 N.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Answer quickly
A Warren girder bridge truss that will be subjected to loads as shown above is to be designed and analysed. All triangles are equilateral triangles and member a-b is 2 m long. Calculate the following: State the nature of the framework. Calculate the reactions at the supports. Using the method of sections (analytical method), calculate the magnitude of the internal forces in member b-c, b-g and g-h and state the sense (nature) of each force
A rectangular reinforced concrete beam has a cross-section dimensions b=400mm andoverall depth h= 800mm. The beam as shown in the image below carries asuperimposed dead load of 12 kN/m (excluding the self-Weight of the beam) andspecified live load of 20 kN/m. The beam has a compressive strength of 30Mpa andreinforcement yield strength of 400 Mpa. Draw the factored shear force and bending moment diagram for all loads includingbut not limited to self weight of the beam
A beam has a uniform dead load and live load has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at the midspan. (MPa) Properties: Beam width = 270 mmBeam height = 375 mmWLL = 14.38 kN/mWDL = 18.41 kN/mSpan of the beam = 8 mPrestressing force = 481 kNeccentricity = 103 mm
R= 9 A three span continous beam ABCD is loaded with ultimate loads as shown in Figure 3. Determine the required plastic moment of resistance assuming uniform section of beam. Assume, p = (25+ R/10) kN, q = (20 + R/5) kN. 10 kN/m L mám D A B 5m 2m Figure 3 2m 3m 2m
Concrete T-beam has been reinforced by bonding a steel plate to its web asshown below. The beam carries a uniformly distributed load of 40kN/m over a simply supported 8m span. Find the maximum deflection of the beam on the assumption that the concrete is fully operative in both tension and compression.(Est = 200kN/mm^2. Econc = 30kN/mm^2; central deflection due uniformly distributed load, total W acting on a simply supported beam of span L= 5WL^3/(384EI)) can someone please answer this question in detail who is confident in this topic with step-by-step calculations & sketch pls. I've asked this question twice now and I've gotten different answers each time so I'm at a bit of a loss. Thank you
A uniformly-distributed load w is supported by a structure consisting of rigid bar BDF and three rods. Rods (1) and (2) are 15-mm- diameter stainless steel rods that have an elastic modulus of E = 198 GPa. Rod (3) is a 22-mm-diameter bronze rod that has an elastic modulus of E = 108 GPa. Use a = 1.4 m and L = 2.7 m. For a load magnitude of w = 28 kN/m, calculate (a) the normal stress in each rod. (b) the vertical deflection of the rigid bar at F. 2a (1) |(2) (3) Answers: (a) 01 = i MPa, 02 = i МPа, and og- i MPa (b) VẸ = mm
A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly distributed load which can be applied over the entire length of the beam if the shearing stress is limited to 1.3 MPa. Answer must be in kN/m. Given: b 130 mm and d-150 mm. 270 mm 150 mm
For the beam shown above with length L = 7 m with the applied uniformly distributed load of w = 13 kN/m, what is the maximum bending stress if the beam has a cross section with the following dimensions:
Determine the Global stiffness matrix of the continuous beam shown. Assume EI is 150kN -m² is constant for each element.*For uniform load Q= 48 kN/m*For concentrated load P= 48 kN
PROVIDE A CLEAR, COMPLETE, AND CORRECT SOLUTION AND FINAL ANSWER
A rectangular beam 100 mm x 200 mm carries a uniformly distributed load of 5 kN/m over its simple span of 5 m. Compute for the maximum shear stress in the beam. Select the correct response: 0.94 MPa 0.38 MPa 0.66 MPa 0.56 MPa