A slab is supported on columns spaced at 6 m c/c apart in both directions. The sizes of the column and column head are 500 x 500 mm and 750 mm x 750 mm as shown in Fig. 14.34a. The superimposed dead and live loads are 2 kN/m² and 4 kN/m2. The height of the floor is 5 m. Design the slab. (Use IS CODE) SECIL CAL 750X750 COLUMN HEAD T C/L- TCAL 3000 3000 3000 1 C/L- 1 3000 3000 COLUMN 3000 COLUMN MIDDLE STRIP STRIP STRIP 6000 (a) PLAN OF INTERIOR PANEL Fig. 14.34a C/L COLUMN STRIP MIDDLE STRIP COLUMN STRIP 6000

A slab is supported on columns spaced at 6 m c/c apart in both directions. The sizes of the column and column head are 500 x 500 mm and 750 mm x 750 mm as shown in Fig. 14.34a. The superimposed dead and live loads are 2 kN/m² and 4 kN/m2. The height of the floor is 5 m. Design the slab. (Use IS CODE) SECIL CAL 750X750 COLUMN HEAD T C/L- TCAL 3000 3000 3000 1 C/L- 1 3000 3000 COLUMN 3000 COLUMN MIDDLE STRIP STRIP STRIP 6000 (a) PLAN OF INTERIOR PANEL Fig. 14.34a C/L COLUMN STRIP MIDDLE STRIP COLUMN STRIP 6000

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

REINFORCED CONCRETE: WSD Method
The beam is loaded uniform deadload of 42 kN/m (including its own weight), and a uniform live load of 48 kN/m. Concrete strength fc' = 21 MPa and steel yield strength fy = 415 MPa, concrete cover is 65 mm from the centroid of the bars. Assume El to be constant. 320 mm 540 mm 7m 2m a. What is the uniform factored load on the beam in kN/m? b. What is the vertical reaction (factored) at B in KN? c. What is the maximum nominal moment can the beam carry if it is to be design as singly reinforced, in kN.m? d. What is the required tension steel area in mm2, at point of maximum positive moment? e. What is the required tension steel area in mm2, at point of maximum negative moment? f. Using simplified calculation, calculate the nominal shear strength provided by concrete near the fixed end, in KN? g. Using 10 mm W-stirrups with fyh = 275 MPa, what is the required stirrup spacing near the fixed end?
Qz- Find the, Critical load Pe using E=2x1ổ Pc Pery 4m
A column ABC is constructed with uniform hollow circular section as shown below. The roof load at the top of column is 50 kN and the floor load at mid height is 150 kN. The compressive stresses in the portion AB and BC are and respectively. 50 kN 200 mm 150 kN 15 mm X-X C.
A singly reinforced beam of dimension 200 x 350 is reinforced with 3-25mm at the bottom. If the concrete has a compressive strength of 17MPa and the steel has a yield strength of 415 MPa, determine if the beam can carry a uniform distributed load of 18 kN/m dead load. The beam has a length of 5m with 40mm concrete clear cover, 10mm enclosed stirrups, and Es = 200 GPa. Use LRFD in the analysis.
3.12: An RCC column is 400 mm 400 mm in section. The column is reinforced with 08 steel bars of 20 mm diameter. The column carries a load of 15 x 10 N. Find the stresses in the concrete and steel bars. Take "E" for steel and concrete as 2.1x 10 N/mm and 1.4 x 10 N/mm 400 mm 400 mm Fig. 3.26 Steel bars 8 Nos/20 mm Concrete
Q1) The R.C slab system shown in Figure (1) supported by column line beams and carries a service live load of 5 kN/m and a service superimposed dead load of 3.5 kN/m in addition to its own weight. Slab thickness is 200mm, all beams are (300x600) mm. All columns are 300mm square, use f-25MPA and f=420MP.. According to the ACI-direct design method, determine the following: 6.0m 7.6m 6.0m (a) Design the middle strip bottom bars of the exterior indicated panel shown, in E-W direction. 6.0m 6.0m 7.6m (b)Design the required steel reinforcement at the exterior corner (C). Figure (1)
DETERMINE THE CONCRETE AND STEEL STRESS AT THE FIXED SUPPORT C.
A simply supported bseam of a beam and slab system, rests on a support of width 450 mm. The clear span of the beam is 10.0 m., The thickness of the slab is 120 mm. The depth of the beam below the slab is 480 mm and the width of the beam is 250 mm. The beam is reinforced with one row of 32 mm diameter steel rods. The total load including the super imposed dead load, live load and its own weight is 25.0 kN/m at service stage. Compute the maximum nominal design shear stress in the concrete.