A slab is supported on columns spaced at 6 m c/c apart in both directions. The sizes of the column and column head are 500 x 500 mm and 750 mm x 750 mm as shown in Fig. 14.34a. The superimposed dead and live loads are 2 kN/m² and 4 kN/m2. The height of the floor is 5 m. Design the slab. (Use IS CODE) CAL C/L 750X750 COLUMN HEAD TCAL 3000 3000 C/L 3000 --- 1 3000 3000 COLUMN MIDDLE 3000 COLUMN STRIP STRIP STRIP 6000 (a) PLAN OF INTERIOR PANEL Fig. 14.34a T COLUMN STRIP MIDDLE STRIP COLUMN STRIP 6000

A slab is supported on columns spaced at 6 m c/c apart in both directions. The sizes of the column and column head are 500 x 500 mm and 750 mm x 750 mm as shown in Fig. 14.34a. The superimposed dead and live loads are 2 kN/m² and 4 kN/m2. The height of the floor is 5 m. Design the slab. (Use IS CODE) CAL C/L 750X750 COLUMN HEAD TCAL 3000 3000 C/L 3000 --- 1 3000 3000 COLUMN MIDDLE 3000 COLUMN STRIP STRIP STRIP 6000 (a) PLAN OF INTERIOR PANEL Fig. 14.34a T COLUMN STRIP MIDDLE STRIP COLUMN STRIP 6000

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

REINFORCED CONCRETE: WSD Method
Design a square base plate to support 10 mm thick pipe column with an inside diameter of 300 mm. The base plate minimum dimension is 500 mm. To design plate thickness, convert the circular perimeter of the pipe into an equivalent square with an area equal to the original circle. The loads are PDL = 850 kN and PLL =420 kN. Assume that the pipe is to rest on a very wide slab. Use A-50 steel and concrete fc’ = 35MPa and LRFD.
A concrete one-way slab has a total thickness of 120mm. The slab will be reinforced with 12 mm diameter bars with fy=275 MPa, fc'= 21 MPa. Determine the area of rebar in mm^2 if the total factored moment acting on 1m width of slab is 23 kN-m width of slab is 23 kN-m. Clear concrete cover is 20 mm.
Referenced concrete n=1
pre stressed conc. solution pls answer
Tributary area Determine the load support by the following with FBD
3.12: An RCC column is 400 mm 400 mm in section. The column is reinforced with 08 steel bars of 20 mm diameter. The column carries a load of 15 x 10 N. Find the stresses in the concrete and steel bars. Take "E" for steel and concrete as 2.1x 10 N/mm and 1.4 x 10 N/mm 400 mm 400 mm Fig. 3.26 Steel bars 8 Nos/20 mm Concrete
A 15 x 25 in. column is reinforced with four No. 9 (No. 29) bars, one in each corner as shown in Figure (a). The concrete cylinder strength is f. = 4000 psi and the steel yield strength is 60000 psi. Determine the axial load strength for zero eccentricity without subtraction of the concrete displaced by the steel, as well as with subtraction of the concrete displaced by the steel. E=0.003, E,-29000. Imperial Metric bar Linear Mass Density Nominal diameter Nominal area 25" bar size size (soft) Ib (in) (mm) (in') (mm") 2.5" -2.5" 0.250 - % 6.35 0.05 32 0.375 = % 9.53 0.11 71 0.500 = 4 12.7 0.20 129 0.625 = % 15.9 0.31 200 0.750 = % 19.1 0.44 284 0.875 = % 222 0.60 387 1.000 = % 25.4 0.79 510 1.126 - % 28.7 1.00 645 1.270- 1% 32.3 1.27 819 No.6 0.167 0.249 3 No. 10 0.376 0.560 #4 No. 13 0.668 0.994 Pn #5 No. 16 1.043 1.552 15" No. 19 1.502 2.235 #7 No.22 2.044 3.042 #8 No 25 2 670 3.973 As No 29 3.400 5.060 A's #10 No 32 4.303 6.404 e varies #11 No.36 5.313 7.907 1.410- 35.8 1.56 1.006…
Q1) The R.C slab system shown in Figure (1) supported by column line beams and carries a service live load of 5 kN/m and a service superimposed dead load of 3.5 kN/m in addition to its own weight. Slab thickness is 200mm, all beams are (300x600) mm. All columns are 300mm square, use f-25MPA and f=420MP.. According to the ACI-direct design method, determine the following: 6.0m 7.6m 6.0m (a) Design the middle strip bottom bars of the exterior indicated panel shown, in E-W direction. 6.0m 6.0m 7.6m (b)Design the required steel reinforcement at the exterior corner (C). Figure (1)
A simply supported bseam of a beam and slab system, rests on a support of width 450 mm. The clear span of the beam is 10.0 m., The thickness of the slab is 120 mm. The depth of the beam below the slab is 480 mm and the width of the beam is 250 mm. The beam is reinforced with one row of 32 mm diameter steel rods. The total load including the super imposed dead load, live load and its own weight is 25.0 kN/m at service stage. Compute the maximum nominal design shear stress in the concrete.