A simply supported timber beam with length L-5m carries a uniformly distributed load w - 8 kN/m. Determine the magnitude of the maximum compression bending stress that occurs in the beam at any location within the 5-m span length. 300 mm L. 100 mm O 16.67 MPa O 21.39 MPa O 19.63 MPa O 10.08 MPa O 15.13 MPa Attempts: 0 of 1 used Submit Answer Save for Later

A simply supported timber beam with length L-5m carries a uniformly distributed load w - 8 kN/m. Determine the magnitude of the maximum compression bending stress that occurs in the beam at any location within the 5-m span length. 300 mm L. 100 mm O 16.67 MPa O 21.39 MPa O 19.63 MPa O 10.08 MPa O 15.13 MPa Attempts: 0 of 1 used Submit Answer Save for Later

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 3: A6m long fix-ended concrete beam has a width of 310 mm and an overall depth of 480 mm. The beam is reinforced with 4-28 mm diameter bars at the bottom and 2 28 mm bars on top. Steel cover measure from the center of the bar is 70 mm. f'e- 28 Mpa and fy - 415 Mpa. Total dead load including beam weight is 22 kN/m. Assuming the analysis is Doubly-reinforced beam. 7. Determine the depth of compression block in mm. 8. Determine design ultimate moment of the section if reduction factor is 0.90. 9. Determine the additional concentrated live load can carry at the midspan.
The T- beam used in a heavy storage warehouse is made of concrete having a specific weight of 125 lb/ft3. Determine the dead load per foot length of beam, and the live load on the top of the beam per foot length of beam. Neglect the weight of the steel reinforcement. (heavy storage warehouse live load = 250 lb/ft2)
A cantilever timber beam with a span of L = 2.6 m supports a uniformly distributed load w. The beam width is b = 250 mm and the beam height is h= 140 mm. The allowable bending stress of the wood is 5.9 MPa. Determine the magnitude of the maximum load w that may be carried by the beam. Answer: w= i eTextbook and Media Save for Later kN/m. Attempts: 0 of 3 used Submit Answer
Q1|| The R.C flat floor slab with outer edge beam as shown in Figure (1). The slab carries a service super- imposed dead load of 3kN/m and a service live load of 3kN/m2 in addition to its own weight. Slab thickness is 200mm and outer edge beam is (500x250) mm, exterior columns are (250x250) mm dimensions. All interior circular columns are 300mm in diameter. Use 12mm bars for slab reinforcement, fe=25MPA and f-420MPA. Then: Using Equivalent Frame Method to find the distribution factor at exterior and first interior joint of Frame A, if story height is 3.8m. 4.0m 6.0m 6.0m • Framie A● 4.0m 4.0m J. 5.0m 4.0m
A reinforced concrete T-beam is to be designed for tension only. The beamwidth is 250 mm. effective depth to bottom bars is 400 mm, flange thickness is 100mm, simple span is 3.6 m and beam spacing is 1.2 m on centres. If the applied designmoment is 300 kn-m, fc’ = 20.7 MPa and fy = 414 MPa. Determine the effective widthof the compression flange and the number of 28 mmφ diameter bars necessary forthe beam.
Wu-100 kN/m 6 m 4 m D Question 9 (PROBLEM 2) A three-member frame ABCD is loaded with ultimate gravity and lateral loads as shown in the figure. The compressive strength of concrete=21MPa, fy=415 MPa, beam width=300mm, beam height=600mm, main bar diameter=28mm, concrete cover-40mm, and stirrups diameter-10mm. Calculate the depth of the neutral axis in the final section in mm. B 4 m A mim. C Pu=115 kN
a beam b = 350mm h = 660mm is reinforced with 2- 28mm compression bars and 4- 36mm tension bar. concrete cover is 60mm from centroid of the bar, if The beam is subjected to a maximum service dead load of 230KN m. determine the maximum service live load the beam can carry. use fc = 21Mpa, fy = 345MPA Select the correct response: MII = 244.02KN-m MII = 390.43KN-m %3D MII = 666.43KN-m MII = 436.43KN-m
Determine the ultimate moment capacity of a reinforced concrete T-Beam with the following properties: Flange Width, bf = 1500 mm Slab Thinckness, tf = 100 mm Beam Width , bw = 250 mm Effective depth, d = 600mm Stength of Concrete, f’c = 20.7 MPa Strength of Steel, fy = 415 MPa Beam is reinforced with 6 – 28mm dia. RSB please answer this thanks
A reinforced rectangular beam with width b and effective depth d is subjected to service live and dead loads (self-weight included) of wL and wD, respectively. If required, compression steel bars are to be placed at a distance d' from the extreme compression fiber. Use fe' = 28 MPa and fy 420 MPa. b= 100 mm d= 200 mm d'= 300 mm L= 320 m wL 210 kN/m wD= 220 kN/m 1. Solve for the area of tension steel bars using es 0.004. 2. Solve for the area of compression steel bars using es 0.004. 3. Solve for the area of tension steel bars using es = 0.005. 4. Solve for the area of compression steel bars using es = 0.005.
A rectangular cross section of a beam is under the bending moment of 60 kips-ft. Determined the Maximum compression and tension stress in the concrete and tensile stress in the rebar. The section is uncracked. b-15 in, h=30 in, d= 28 in f=4000 psi, Ec-3,600,000 psf fy= 60,000 psi, Es-29,000,000 psf Rebar= 3 -No. 6 h -As
Question 3 of 10 View Policies Current Attempt in Progress Answer: Wo A The steel beam has the cross section shown. The beam length is L = 5.8 m, and the cross-sectional dimensions are d = 400 mm, bf = 210 mm, tf = 14 mm, and tw = 7 mm. Calculate the largest intensity of distributed load wo that can be supported by this beam if the allowable bending stress is 160 MPa. A 72 Save for Later Wo B 72 C kN/m - / 10 E ||| d 600 Attempts: 0 of 3 used Submit Answer
A simply supported bseam of a beam and slab system, rests on a support of width 450 mm. The clear span of the beam is 10.0 m., The thickness of the slab is 120 mm. The depth of the beam below the slab is 480 mm and the width of the beam is 250 mm. The beam is reinforced with one row of 32 mm diameter steel rods. The total load including the super imposed dead load, live load and its own weight is 25.0 kN/m at service stage. Compute the maximum nominal design shear stress in the concrete.