Problem A spiral column 600 mm in diameter has an unsupported height of 2.4 m. The column is bent in single curvature and is braced against side sway. Steel ratio is at 1.70%. Given: Axial loads at service condition Dead Load, DL 3,359 kN Live load, LL-1,563 kN Compressive strength, fe' 27.5 MPa Steel yield strength, fy = 413 MPa Find the number of 32 mm diameter bars considering ultimate design load condition. (round up to the next whole number)

Problem A spiral column 600 mm in diameter has an unsupported height of 2.4 m. The column is bent in single curvature and is braced against side sway. Steel ratio is at 1.70%. Given: Axial loads at service condition Dead Load, DL 3,359 kN Live load, LL-1,563 kN Compressive strength, fe' 27.5 MPa Steel yield strength, fy = 413 MPa Find the number of 32 mm diameter bars considering ultimate design load condition. (round up to the next whole number)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
need answer thank you
Hello help me answer this. Thank you.
Find the maximum allowable value of P for the column. The cross-sectional areas and working stresses (ow) are shown in the figure. |2P Steel: A = 500 mm2 Ow = 120 MPa P Timber: 4P A = 2000 mm? Ow = 12 MPa Concrete: A = 8000 mm? O = 16 MPa
ASAP!!! NEED RIGHT COMPLETE SOLUTION !!!
S9. Knowing that the allowable normal stress for the steel used is 150 MPa, select the most economical metric wide-flange beam to support the loading shown in Figure 9.0. 50 kN/m A D B -2.4 m- 0.8 m 0.8 m Figure 9.0 $10. Determine the average shearing stress in the web of the beam indicated and check whether the design obtained earlier for that beam is acceptable, knowing that the allowable shearing stress for the steel used is 110 MPa. Consider the beam of $9 above.
A rectangular tied braced column is reinforced with 6-28mm bars as shown in the figure below. Check the adequacy of the column for the following gravity loads: - - - - - - Service dead load = 1050kN Service live load = 850 kN Service dead load moment = 39 kN-m Service live load moment = 27 kN-m top=bott. = 1.0 40 lu = 5.0m f = 27.6 N/mm², fy = 414 N/mm² axis of bending 500mm Ties 10mm@300c/c } 350mm At eccentricity of 40mm P M +40 + 500mm MU +40- P Top end Bott. end
The wood beam has an allowable shear stress of tallow = 7 MPa. Determine the maximum shear force V that can be applied to the cross section.
Using Table 10.2, select a column shape for an axial deadload of 400 kips and a live load of 600 kips. The unbraced height about thex axis is 16 ft and about the y axis is 4 ft. The steel is to have a yield stress of50 ksi and K is assumed as 1.0.
AWT305 x 41 standard steel shape is used to support the loads shown. Assume w= 58 kN/m, LAB = 1.8 m, LBc=3.6 m, and Lco = 1.8 m. Consider the entire 7.2 m length of the beam and determine: (a) the maximurm tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer). y LAB LBC LCD WT305 x 41 Answer: (a) Omax,T МPа (b) omax,C= МРа
Show complete solution with FBD and handwritten.
Problem 1. The composite beam shown below carries a cantilevered load of 10 kN. The beam consists of one 30 x 124 mm plate and four 12 x 50 mm plates. They are pinned together at 120 mm intervals with round pins. The pin material has a shear strength of 159 MPa. Compute the minimum acceptable diameter for the pins. O O O O O O O -0 O 0- O 1000 mm Do O -120 mm (typ) O O O P = 10 KN 30 x 124 mm 12 x 50 mm (typ)