a) If the beam is to be designed for a balance condition, find the required area of steel reinforcement, design balanced moment, and the corresponding service live load moment. b) Find the maximum steel area, the maximum design moment, and the corresponding service live load moment if the beam is to be desined as singly reinforced.

a) If the beam is to be designed for a balance condition, find the required area of steel reinforcement, design balanced moment, and the corresponding service live load moment. b) Find the maximum steel area, the maximum design moment, and the corresponding service live load moment if the beam is to be desined as singly reinforced.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. The details of the cantilever beam are shown below. Use f'c = 28 MPa, fy = 415 MPa, and fyt = 275 MPa. Notes:• All dimensions are in millimeters.• Column reinforcement not shown for clarity• Column and beam are neither exposed to weather nor contact with the ground.• Analyze as singly reinforce beam only.• Neglect the weight of the beam.• Concrete isnormal weight and reinforcements are galvanized. d. What is the flexural capacity of the beam at face of support in kNm? e. What is theshear capacity of the beam at face of support in kN? f. What is the maximum Pu (kN) that can be applied at the free end of the beam consideringflexure and shear? g. What is the requiredminimum cut length (mm) of each stirrup? Roundyour answer to nearest safe25 mm.
(2) 4 0 5 211 5 4 #9 4 "1 16 #3" ft-k fé = 3 ksi, M = 90 NWC. The section is cracked. Computer the bending stresses in the beam by using transformed-area metho
Please answer fast ASAP
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
Calculate the design bending strength for the doubly reinforced rectangular section where A’s = 2500 mm2 f’c= 30 MPa & fy = 350 MPa if As =8500 mm2
Question # 1: The composite beam is made of steel (4) bonded to brass (B) and has the cross section shown. If the allowable bending stress for the steel is (sallow) st = 180 MPa, and for the brass (sallow) br = 60 MPa, determine the maximum moment (M) that can be applied to the beam Ebr 100 GPa, Est= 200 GPa B Question # 2: Determine the maximum shear stress acting at section a-a in the beam. 150 N/m m 8000 N Bla 1.5 m 1.5 m 50 mm 50 mm 200 mm 175 mm 200 mm -B 400 mm 75 mm 600 mm 75mm
Combined Stresses Given Hollow Steel Section (HSS) that is 4"x6" and 1/2" thick, with axial and transverse loading shown, determine the total normal stress at a. The 5k load on the bottom of the beam b. At the mid-span in the middle of the beam C. At the 10k load on top of the beam 5k 10k A 5' 10' 5' B CENTROID 4" 5 k 3k 8k 6" 2' 6.25k 8.75k +6.25k SECTION +1.25k 'V" -8.75k +43.75k-ft. +31.25k-ft. 'M' 8k 5 k + tension P = Ok %3D
S9. Knowing that the allowable normal stress for the steel used is 150 MPa, select the most economical metric wide-flange beam to support the loading shown in Figure 9.0. 50 kN/m A D B -2.4 m- 0.8 m 0.8 m Figure 9.0 $10. Determine the average shearing stress in the web of the beam indicated and check whether the design obtained earlier for that beam is acceptable, knowing that the allowable shearing stress for the steel used is 110 MPa. Consider the beam of $9 above.
A prestressed beam has a width of 300 mm and depth of 600 mm. It is subjected to a bonded prestress tendon having an area of 590 mm2 acting at a distance 550 mm from the compression, face of the member. fc' = 34.6 MPa, fpu = 1860 MPa, fpy = 0.85fpu (stress-relived strands).COMPUTE THE STRESS IN THE PRESTRESS REINFORCEMENT AT NOMINAL STRENGTH (MPa)
2. Per ACI318-19, choose the correct value of the strength reduction factor ø for the flexural capacity of a beam with ɛ = tension face. 0.0032, where & is the strain for steel reinforcement closest to the (A)0.9 (B) 0.85 (C) 0.75 (D)0.65
B4
QUESTION 1A concrete floor slab measuring 6 m x 3 m is simply supported on one side brick load-bearing walls along the 6 m sides. The concrete slab is 200 mm thick and reinforced at the bottom as follows. a. Main reinforcement (short span i.e the bars are parallel to the short span), Y12, shape code 34 @ 125 mm centre to centre,b. Distribution reinforcement (long-span i.e the bars are parallel to the long span), Y 10, shape code 20 @ 300 mm centre to centre,c. Concrete cover, 30mm,d. Concrete strength, 40MPa. Draw the reinforcement layout for this slab, in plan and section, indicating all thereinforcement and necessary information required by the contractor. Calculate and indicate the number of bars required on your drawing. You do not need to calculate the bar lengths and the curtailment. Neat drawing please