a beam b = 350mm h = 660mm is reinforced with 2- 28mm compression bars and 4 - 36mm tension bar. concrete cover is 60mm from centroid of the bar, if The beam is subjected to a maximum service dead load of 230KN -m. determine the maximum service live load the beam can carry, use fc = 21Mpa, fy = 345MPA Select the correct response MII = 244.02KN-m MII = 390.43KN-m MII = 666,43KN-m MII = 436.43KN m

a beam b = 350mm h = 660mm is reinforced with 2- 28mm compression bars and 4 - 36mm tension bar. concrete cover is 60mm from centroid of the bar, if The beam is subjected to a maximum service dead load of 230KN -m. determine the maximum service live load the beam can carry, use fc = 21Mpa, fy = 345MPA Select the correct response MII = 244.02KN-m MII = 390.43KN-m MII = 666,43KN-m MII = 436.43KN m

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Related questions

Q: Given: T Beam A shown below spans 32 ft (simple span) and supports the floor system shown. Typical…

Q: A flat slab is supported by 18"x18" columns spaced at 26 ft in both directions. The slab is 10" and…

A: F'c =" data-mce-style="box-sizing: border-box; display: inline-block; line-height: 0; text-indent:…

Q: A rectangular beam has a width of 300mm and an effective depth pf 537.50mm to the centroid of…

A: Given:width, b = 300mmEffective depth, d = 537.50mm6-28 mm tensile bar in two rows2-22 mm…

Q: Design a one-way slab for inside of a RC Building. NWC. Use slab thickness = 6/1/2" Additional WDL =…

A: One-way slab : Because of its geometry, a one-way slab is a slab that is supported by parallel walls…

Q: Wu-100 kN/m 6 m 4 m D A Question 6 (PROBLEM 2) A three-member frame ABCD is loaded with ultimate…

Q: Calculate maximum deflection of the concrete beams Check the suitability of the section assuming the…

Q: 1.2m 10 cm 7cm -7cm This concrete beam has four A-35 steel rods of one centimeter diameter and a…

A: Stresses in Concrete Beam : A concrete beam is a load bearing unit which is used to carry both…

Q: A T-beam floor consists of 15 cm thick RC slab monolithic with 30 cm wide beams. The beams are…

Question

a beam b = 350mm h = 660mm is reinforced with 2- 28mm compression bars and 4- 36mm tension bar. concrete cover is 60mm from centroid of the bar, if
The beam is subjected to a maximum service dead load of 230KN m. determine the maximum service live load the beam can carry. use fc = 21Mpa, fy =
345MPA
Select the correct response:
MII = 244.02KN-m
MII = 390.43KN-m
%3D
MII = 666.43KN-m
MII = 436.43KN-m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

USE NSCP 2010 A simply supported beam is reinforced with 4 – 28 mm ø at the bottomand 2 – 28 mm ø at the top of the beam. Steel covering to centroid ofreinforcement is 70 mm at the top and bottom of the beam. The beamhas a total depth of 400 mm and a widthof 300 mm. fc’ = 30 MPa, fy = 415 MPa. Balanced steel ratio ρb = 0.031.Compute the ultimate moment capacity of the beam in kN-m. Usereduction factor of 0.90
A beam has a width of 300 mm and an effective depth of 480 mm strength Pc= 34 MPa. Steel yield strength fy=415 MPa. The section is to be reinforced for tension only and the effective concrete cover is 70 mm. Deadload moment is 140 kN-m and the liveload moment is 180 kN-m. Use 2010 NSCP with t= 0.005. A. What is the governing steel ratio? B. What is the maximum number of bars needed for a 25mm diameter reinforcements? C. What is the minimum number of bars needed for a 25mm diameter reinforcements?
3. A rectangular beam has the following properties: Width, b = 400 mm Effective depth, d 620 mm Tension bars, 10 pcs 28-mm-diameter Compression bars, 3 pcs 25-mm-diameter d' = 70 mm fy = 415 MPa f'c = 22 MPa Determine the design strength of the beam and the safe service live load if the service dead load is 320 kN-m.
Situation #2: A rectangular beam has the following properties: Width, b = 400 mm 415 MPa Effective depth, d = 620 mm 22 MPa Tension bars, 10 pcs 28-mm-diameter Compression bars, 3 pcs 25-mm-diamter d' = 70 mm fy= = fc' = Determine the design strength of the beam and the safe live load if the service dead load is 320 kN.m
Please use the NSCP 2015. Thank you.
9.4- A concrete slab with 180 mm thickness support dead load 5kN/m² include self- weight and service live load 4kN/m2, find: 1- Adequacy of slab thickness. 2- Steel area required at point 1, 2, 3&4. 3- Total load on beam AB and DC. Use Ø12 mm, f = 28MPA and fy = 400MPA 5 20 m- 5.20 m- -5.00 m- -5.20 m- opening 6.00 m B 2 6.00 m D 2.00 m
in 21- ő A steel beam is reinforced by three steel rods. The modulous of elasticity for concrete is 20Gpa and for steel is 200Gpa. Maximum allowable stress for concrete is 9.45Mpa and for steel is 140Mpa. Calculate the largest allowable positive WBT bending moment in the beam. иа mo maod motinu od o boblow need sved Ha bus 400mm aidT (alonnerlo ert to rigiow stongi)/4000E of Trup 200-0 signs or botuesom sWnworla es berloss M bris V zsra erli owob stiW maod sdi to mergeib insm brol bus borlism tuo sallimill nollor 10 nige over on The modulus of elasticity for concrete is 20Gpa and for the steel is 200 Gpa. Allowable stress for concrete is 9Mpa and for steel is 140Mpa. Calculate the maxium allowable bending momemt that can be applied per metal rod of the concrete slab. 150mm 200mm D=16mm 140 mm -22mm Diameter TOPABA t 50mm T 140 mm 140 mm 140 mm
Please show complete and detailed solution.
Please answer with complete detailed solution. Thank you.
Wed 20 Apr 45% Stresses in Beams part 5 thi qar (5 of 6) Second Class Lecturer: Dr. Ali Al Asadi Example 3: The beam shown below has a cross section of channel shape with width b=300 mm and height h=80 mm, the web thickness is t=12 mm. Determine the maximum tensile and compressive stresses in the beam due to uniform load. 300mm 3.2 KN / m 80 mm -12 mm 3 m 1.5 m 14.4 KN EM, =0 B,x3-14.4x2.25=0 B=10.8 KN B F = 0 A A,+10.8-14.4=0
USE NSCP 2010 A rectangular beam reinforced for both tension and compression barshas an area of 1450 mm² for compression bars and 4350 mm² fortension bars. The tension bars and compression bars are placed at a distance of 600 mm and 62.5 mm respectively from the top of thebeam. The beam width 300 mm, fc’ = 21 MPa, fy = 415 MPa andtension steel covering is 60 mm.If it is 8 m-simply-supported beam that carries three concentratedservice live loads P applied at three quarter points of the beam (exceptat the supports), neglecting the self weight of the beam, determine themaximum value of service load P in kiloNewtons.
An RCC beam 400*600 (effective depth) is reinforced with 4 no. 25mm diameter bar the beam is subjected to BM 150KNm. find the stress setup in steel and concrete. Consider M20 Fe415