Q3/ Determine the mid-span short-term deflection of a simply supported beam with the section shown in figure below. Design data - Concrete strength fc'=30MPa. - Span length 8.0m - Area of tensile steel reinforcement: As=1500mm² - Area of compressive steel reinforcement: As'=1500mm² - Loading Additional dead load -5kN/m (uniform distributed load) • Live load -5kN/m (uniform distributed load) T DUDUG As As boand 0.30m 0.70m d=0.60m d'=0.10m

Q3/ Determine the mid-span short-term deflection of a simply supported beam with the section shown in figure below. Design data - Concrete strength fc'=30MPa. - Span length 8.0m - Area of tensile steel reinforcement: As=1500mm² - Area of compressive steel reinforcement: As'=1500mm² - Loading Additional dead load -5kN/m (uniform distributed load) • Live load -5kN/m (uniform distributed load) T DUDUG As As boand 0.30m 0.70m d=0.60m d'=0.10m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 1 The T-section beam shown in the figure below is required to resist an ultimate design moment of Mu = 460 kN m. The characteristic materials strengths are fy = 410 N/mm2 and fou 20 N/mm2. Calculate the area of reinforcement required. %3D b = 685mm ht = 90 mm d = 560 mm bw = 300 mm
A reinforced concrete T-Beam has a width of 800mm and a thickness of 50mm. It has an effective depth of 300mm and is reinforced at the bottom with a total steel area of 1800sq.mm. If the web thickness of the T-beam is 200mm, with a concrete strength of fc' = 20MPa and yield strength of steel fy= 400MPa. Assume steel yields. The value of the area subjected tocompressive stress is _sq.mm A. 42,353 sq.mmB. 42,553 sq.mmC. 42,153 sq.mmD. 41,953 sq.mm
A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.0 m, web width of 250 mm and overall depth of 500 mm. The tensile reinforcement consists of 6 - ø20 mm bars in two rows with 25 mm vertical clear spacing. Use material strength f'c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = _______ Depth of uniform stress block at ultimate stage in mm to the neares whole number = _______ Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places = __________
A rectangular R.C beam of detail shown in Fig. subjected to bending moment of (150 kN.m), n=9, f'c = 28 Mpa, fy = 413Mpa, use the working stresses method (Cracked State) to find: 1- Maximum compression stresses in concrete. 2- Maximum tensile stresses in steel reinforcement. 4025mm 250 mm 500mm 70 mm
Seatwork The beam shown is prestressed by using a bonded (stress relieved tendons) with a specified tensile strength of prestressing tendons strength fpu=1350 MPa, fc'=35 MPa. The area of prestressed reinforcement in tension zone Aps=1000 mm?. The specific yield strength of prestressing tendons sd, foy=1160 MPa. а. What is the value of the stress in prestressed reinforcement at nominal strength (Aps) b. What is the value of the depth of the compression block. С. What is the ultimate moment capacity of the prestressed beam. 0.85fc' 430 NA |(d-a/2) · A=1000 T=Ap.Sps 250
a concrete floor slab 100mm thick is cast monotholic with concrete beams 2.0 m on centers. the beams have a span of 4.0m, web width of 259 mm and overall depth of 50 mm. the tensile reinforcement consists of 6-⌀20 mm bars in two rows with 25mm vertical clear spacing. use material strengths f'c=21MPa and fy=415MPa. calculate the ff considering a T-geometry: 1. effective flange width of an interior beam in mm 2. depth of uniform stress block at ultimate stage in mm to the nearest whole number 3. tensile steel strain compatible strain of 0.003
Please solve with complete detailed solution. Thank you.
A rectangular fixed supported beam has the following properties. Compression steel if required shall have its centroid "d " mm from the extreme fiber. Calculate the required steel area (mm) at the midspan and end supports of the beam. Sketch the location of the reinforcements. Use 23.6 kN/m for the unit weight of the concrete. Round off your final answer in 3 decimal places. Given: width of beam, b = 450 mm depth of beam, h = 650 mm clear cover up to center of tension 60 mm bars= d'= 65 mm f'c = 35 MPa fy = 415 MPa wDL = 72 kN/m wLL = 63 kN/m Length of beam = 12 MIDSPAN: Required Tension Steel Area = mm? Required Compression Steel Area (if needed) - mm2 END SUPPORTS: Required Tension Steel Area = mm? Required Compression Steel Area (if needed) - mm?
A cast iron 3m long is completely filled with concrete and used as a vertical strut. If the externaldiameter of the tube is 450mm and the wall is 35mm thick, determine the maximum compressiveload the composite strut can support if the stress in the concrete is not 2N/mm2? By how muchshould the strut shorten under this load? For cast iron EA= 100GN/m2 and for the concrete EB=10GN/m2?
A concrete floor slab 100mm thick is cast monolithic with concrete beams 2.0m on centers. The beams have a span of 4.2m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm diameter bars in two rows with 25mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = Depth of uniform stress block at ultimate stage in mm to the nearest whole number = Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places =
H.W.5: For the simply supported beam shown below reinforced by 4025 bars (fy= 420 MPa), the concrete strength (f= 21 MPa) evaluate the following: 1- Check the actual flexural stresses in concrete and steel if the span length equal to (4 m), dead load 8 kN/m including self-weight of the beam, live load equal to 10 kN/m. 2- The length of beam span that makes the concrete in tension face starts to crack. 3- The actual stress in concrete and steel if the span length of the beam is equal to 7 m. WI= 10 kN/m Wd=8 kN/m 420 mm 500 mm 마 350 mm
13