Q1|| The R.C flat floor slab with outer edge beam as shown in Figure (1). The slab carries a service super- imposed dead load of 3kN/m2 and a service live load of 3kN/m? in addition to its own weight. Slab thickness is 200mm and outer edge beam is (500x250) mm, exterior columns are (250x250) mm dimensions. All interior circular columns are 300mm in diameter. Use 12mm bars for slab reinforcement, fe=25MPA and f-420MPA. Then: Using Equivalent Frame Method to find the distribution factor at exterior and first interior joint of Frame A, if story height is 3.8m. 4.0m 6.0m 6.0m • Frame A● 4.0m 4.0m 5.0m 4.0m

Q1|| The R.C flat floor slab with outer edge beam as shown in Figure (1). The slab carries a service super- imposed dead load of 3kN/m2 and a service live load of 3kN/m? in addition to its own weight. Slab thickness is 200mm and outer edge beam is (500x250) mm, exterior columns are (250x250) mm dimensions. All interior circular columns are 300mm in diameter. Use 12mm bars for slab reinforcement, fe=25MPA and f-420MPA. Then: Using Equivalent Frame Method to find the distribution factor at exterior and first interior joint of Frame A, if story height is 3.8m. 4.0m 6.0m 6.0m • Frame A● 4.0m 4.0m 5.0m 4.0m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

reinforced Concrete
A 500-N concrete block is to be lifted by the pair of tongs shown. 500 N 45 mm 90 mm 45 mm 90 mm 75 mm D 105 mm E 360 mm 315 mm 500 N G Determine the normal force (this is horizontal) in N perpendicular to the friction force on each tong in contact with the block.
Find the safest value of load "P" for the beam loaded shown. fc'=35MPA, Use GRADE 420 steel bar and n=10 The answer is kN. Assume unit weight of concrete = 24kn/cu.m. 200 3 m 1 m toort twit 3P 70 200 2-20 mm O 330 3. BEAM 4-32 mm Ø 300 100 DIMENSIONS ARE IN "mm"
A concrete one-way slab has a total thickness of 120mm. The slab will be reinforced with 12 mm diameter bars with fy=275 MPa, fc'= 21 MPa. Determine the area of rebar in mm^2 if the total factored moment acting on 1m width of slab is 23 kN-m width of slab is 23 kN-m. Clear concrete cover is 20 mm.
5.6 The dimension of a reinforced concrete simply-supported beam supported beam is bxh= 200mm × 500mm, a̟ = 35mm , the concrete is C30, the design value of shear force is V =1.4×10° N, the stirrup is HPB300 grade steel. Please calculate the stirrups required.
PLEASE HELP
The dimensions for a reinforced concrete beam are given as: b = 300mm d = 400mm d’ = 75mm It is to be designed for a service dead load moment of 30kN-m and a service live load moment of 40kN-m. Suppose f’c = 21MPa and fy = 276MPa, how many 20-mm bars are required to reinforced the beam in terms of steel area?
using the table below, answer the question
Please answer with each steps.
H.W.5: For the simply supported beam shown below reinforced by 4025 bars (fy= 420 MPa), the concrete strength (f= 21 MPa) evaluate the following: 1- Check the actual flexural stresses in concrete and steel if the span length equal to (4 m), dead load 8 kN/m including self-weight of the beam, live load equal to 10 kN/m. 2- The length of beam span that makes the concrete in tension face starts to crack. 3- The actual stress in concrete and steel if the span length of the beam is equal to 7 m. WI= 10 kN/m Wd=8 kN/m 420 mm 500 mm 마 350 mm
Given a concrete column that would be required to support loads of Pu=400kips and Mu=50 kip-feet, we will determine the column interaction curve and decide if the column is adequate for this particular application. The column will be a 14”x14” square, tied column with #9 bars at the corners. The center of the reinforcement in each corner is 3” from each of the sides. The f’c of the concrete is 4 ksi and the reinforcement is Grade 60. Determine if the column is acceptable for this application. Calculate the value of Mu and Pu.