4.Recent trends in use of new materials such as advanced composite materials and new testingtechniques employed. Answer below questions using your own words and understanding.(a)The column is 3m long and has 6 numbers main vertical steel of 12mm diameter.(i)Calculate the weight of 12mm diameter reinforcement steel providing suitable formulaand calculations? Neglect bends.

Answered: Image /qna-images/answer/39fd879f-f9aa-4d59-90d1-f3aa0ca26a48.jpg

Recent trends in use of new materials such as advanced composite materials and new testing techniques employed. Answer below questions using your own words and understanding. 4. (a) The column is 3m long and has 6 numbers main vertical steel of 12mm diameter. (i) Calculate the weight of 12mm diameter reinforcement steel providing suitable formula and calculations? Neglect bends.

Recent trends in use of new materials such as advanced composite materials and new testing techniques employed. Answer below questions using your own words and understanding. 4. (a) The column is 3m long and has 6 numbers main vertical steel of 12mm diameter. (i) Calculate the weight of 12mm diameter reinforcement steel providing suitable formula and calculations? Neglect bends.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A high-strength steel band saw, 29 mm wide, runs over pulleys 900 mm in diameter. What minimum thickness of the steel band can be used without exceeding a flexural stress of 290? Assume E = 210 GPa. Answer must be in mm.
A high-strength steel band saw, 27 mm wide, runs over pulleys 1000 mm in diameter. What minimum thickness of the steel band can be used without exceeding a flexural stress of 350? Assume E =230 GPa. Answer must be in mm.
Solution w/FBD
Please help, I promise to give good feedback. Please do not just guess. Thank you!
A simply supported wood beam, reinforced with steel plates, has the cross section shown. The beam carries a uniformly distributed load of 16 kN/m over the middle half of its 4-m span. If modular ratio is equal to 15, determine the largest bending stresses in the wood and steel. 96 mm 96 mm -200 mm 8 mm 240 mn 8 mm
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 25 kips, w = 3.6 kips/ft, LAB = 5.6 ft, LBC = 5.6 ft, and LcD = 16.8 ft. Determine the magnitude of the maximum bending stress in the beam. LAB Answer: Omax = i B LBC C ksi W LCD D ZOQ Q 214% TOP BARI ENG 11:41 am 35 28/04/2023 8 cores
!
Use the giuven values: Aluminum: E = 10 x 106 psi, α = 12.8 × 10-6 in/(in·°F) Bronze: E = 12 x 106 psi, α = 10.5 × 10-6 in/(in·°F) Show you complete solution.
Subject: Steel design- Bolted Steel Connection - Bolted Subjected to Eccentric Loads *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten
The answer is close to 60 Ksi. I need help showing the work to get the answer . Please include units. Thanks
Question (3). Design Exercise (Selecting initial dimensions) A steel cross section of a bridge deck is shown in Figure 3. The cross section is subjected to a maximum bending moment of 43810 kNm. The length L is 4m. Available plate thicknesses (t) are 20 mm, 22 mm and 25 mm. The yield strength () is 355 MPa. Determine the initial dimensions of b and Cw, which can be used for detailed design of the bridge deck. Assume failure of the cross section mainly governs by in-plane bending. State all other assumptions made during this calculations. 60° 2b Ma