Q- A rectangular column section of 250mm x 400mm is reinforced with five steel bars of grade Fe 500, each of 20mm diameters. Concrete mix is M30. Find the axial load on the column section with minimum eccentricity as per IS: 456-2000 using limit state method.

Q- A rectangular column section of 250mm x 400mm is reinforced with five steel bars of grade Fe 500, each of 20mm diameters. Concrete mix is M30. Find the axial load on the column section with minimum eccentricity as per IS: 456-2000 using limit state method.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A simply supported beam has a height of 600 mm and a width of 300mm. Determine the maximum safe live…

Q: Design Slab DEGH of the floor system shown below. Dead load pressure including the slab's weight is…

A: Solution: Given: DL = 5.3 KPa LL = 2.4 KPa fc = 21 MPa fy = 345 MPa beam = 350 x 500 mm use 12 mm…

Q: The working load capacity of a column of size 300 mm x 600 mm with minimum percentage of steel is…

Q: Assignment(1):- QI-For the rectangular reinforced concrete section shown in fig(1) .Answer the…

A: Given:- d = 420 fck = 25 fy=420

Q: The floor framing reinforced concte structure is shown plan oF in the figure. The beams 280mm wide…

A: Load transfer from slab to beam is one of the fundamental for the design of any girder and slab,…

Q: 1. A rectangular beam has b = 300mm, d = 500mm, As = 6 - 36mm diameter bars, fc' = 28.6 MPa, fy =…

A: Answer: We are given Beam width b = 300 mm Effective depth d = 500 mm Area of steel As = 6-36 mm…

Q: :Design a concrete column shown in figure using fe'-28 MPa, fy- 420 MP Itimate applied load. P=545…

A: A concrete column is normally a composite column that consists of steel and concrete also in…

Q: The column is reinforced with 10 32-mm bars distributed around the perimeter. Load Pn will be…

A: When the load acting on the column is offset from the centroid of the column, it causes bending of…

Q: SHOW ALL SOLUTIONS a. Height of Compression Block in mm b. Area of the effective concrete for…

A: "Since you have posted a question with sub-parts. We will solve the first three sub-parts for you.…

Q: 2. From the figure shown, fc' = 20 MPa, fs = 140 MPa, and n = 12. Determine the moment capacity of…

A: Answer To calculate the Moment capacity of concrete and steel we have equation of stress in…

Q: (3) for Normal weight Concrete, using ACI Code and recommendation for high strength concrete, to…

A: Solving first questionGiven datacompressive strength of concrete given in table findmodulus of…

Q: 36. A vertical concentric load of 1800 N is supported by a tapering concentric column. The column…

Q: Q-A rectangular column section of 250mm x 400mm is reinforced with five steel bars of grade Fe 500,…

A: Given- Dimensions of section- 250 mm×400 mm 5 steel bars of Fe500 grade, Diameter d=20 mm, M30 grade…

Q: 1. If column AB is made from high strength pre-cast concrete and reinforced with four 20 mm diameter…

A: Given: σallowConcrete=18 MPaσallowSteel=170 MPa

Q: A rectangular beam has a width of 283mm and an effective depth of 461mm. It is reinforced with…

Q: Figure 1 shows the plan view of an exhibition hall with dimensions L, x L2. The structure is to be…

A: Given data:- Concrete strength ( fck ) = 30.5 MPa Reinforced grade ( fy ) = 472 MPa Height of…

Q: A W18 x 40 floor beam supports a 4-inch-thick reinforced concrete slab with an effective width b of…

A: Given; W18 x 40 floor beam fc'= 4 ksi Positive service load moment =290 ft-kips Effective width b =…

Q: Q3) Consider the rectangular reinforced concrete section given below. Calculate the moment capacity…

A: Width of beam, b = 300 mm Total depth, D = 600 mm Effective depth, d' = 35 mm Effective cover, d…

Q: L (m)=2.8 h (mm)=375 hs (mm)=325 b (mm)=275 (Ơst)allow (MPa)=150 (Ơconc)allow (MPa)= 18

A: Following Indian standard code IS 456 - 2012 The ultimate moment of resistance:(Limit State…

Q: The slab of a residential building of size 4.3 m × 6 m is simply supported on all the ir sides on…

A: Solution:Thickness: lx>3.5take ld=25 i.e d=l25d=430025=172mm~175mmD=200mmEffective…

Q: A reinforced concrete column contains longitudinal steel equal to 1 per cent of net cross-sectional…

Q: The material of the beam given bclow is C3545 - B500C and it is good quality concrete. The cODcrete…

A: c)13 beam width bw=700mmbeam thickness=350mmfy=500Mpafc=35MpaSupport moment of the…

Q: A rectangular beam has a width of 300 mm, and effective depth d=570 mm to centroid of tension steel…

Q: A circular Column has dia of D = 30 in. Concrete Compressive strength at 28 days is (4 +15)ksiand…

A: Circular column diameter = 30in f'c = 4+15 = 19ksi fy = (60+15) = 75ksi

Q: A w = 40 kN/m 8 m 270 KN L Concrete: E=2.5*(10)³ N/mm² 350 mm. 550 mm

Q: 3. A reinforced rectangular concrete beam having a width of 300 mm, effective depth of 500 mm, fc’ =…

A: As per bartleby guidelines , experts are allowed to solve only first three parts. Please post other…

Q: PROBLEM 2. If the beam in Problem 1 is to be replaced by a rectangular beam below using a concrete…

A: From the problem 2, it is required to find out the whether the beam is safe for design or not.

Q: AND CLEAR SOLUTION". YOU MAY BASED FROM Section at C Wox n 45 kN/m 3.0m d'u 20mm

A: P =1.6 LL+ 1.2 DL = 1.6×52+3.2×112 = 217. 6 Kn μ = 1.6×11+1.2×28…

Q: A circular column is subjected to an un-factored load of 1600 kN. The effective length of the column…

Q: A rectangular beam has a width of 298mm and an effective depth of 465mm. It is reinforced with…

Q: Determine the theoretical nominal moment capacity of the beam shown if fy = 420 MPa and fc' = 28…

A: Given - Fy = 420Mpa F'c = 28 Mpa To find-Nominal moment capacity of beam

Q: 1. If column AB is made from high strength pre-cast concrete and reinforced with four 20 mm diameter…

A: Given: σallowConcrete=18 MPaσallowSteel=170 MPa

Q: beam has a width of 300 mm and an effective depth of 480 mm strength Pc= 34 MPa. Steel yield…

A: Answers are boxed.

Q: HW 2-4 Calculate the cracking moment (resisting moment) for the unreinforced concrete beam shown.…

A: Step 1Given data:b=10inh=16infc′=3,000psiThe internal couple methodThe lever arm of the rectangular…

Q: A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with d-20-mm-dismeter bars…

Q: Q-A rectangular column section of 250mm x 400mm is reinforced with five M30. steel bars of grade Fe…

A: Given data- Rectangular column section- 250 mm×400 mm,5 steel bars, Fe500,dia d=20 mm,M30 concrete,…

Q: Estimate for the concrete, formworks, reinforcement requirement of Beam GG-36. Length of Beam 1 =…

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

Q- A rectangular column section of 250mm x 400mm is reinforced with five steel bars of grade Fe
500, each of 20mm diameters. Concrete mix is M30. Find the axial load on the column section with
minimum eccentricity as per IS: 456-2000 using limit state method.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate maximum deflection of the concrete beams Check the suitability of the section assuming the code limitation of L/240. If maximum deflection doesn’t meet the code requirement, propose your solution
Concrete designs, ultimate single , i need solutions in 10 minutes please. Q/determine the live load can be applied on the beam shown in fig. use (fc'=21MPa) and (fy=420MPa).
COMPLETE SOLUTION WITH F.B.D. A reinforced concrete column 400 mm in diameter is designed to carry an axial compressive load of 400 KN. Determine the required area of reinforcing steel if the allowable stresses are 6 MPa and 120 MPa for the concrete and steel, respectively. Use Econcrete = 14 GPa and Esteel = 200 GPa.
The cross section shown is for the fixed support of a propped beam that carries an allowable ultimate moment of 60 kN-m. The concrete is lightweight consisting of a lightweight coarse aggregate and a mixture of a lightweight and normal weight fine aggregate. The total volume of fine aggregate is 15 m3 and 7m3 of it are lightweight. Determine the following if the compressive strength of the concrete is 25 MPa, fy=420 MPa and the weight of the concrete is 1600 kg/m3: (a) Cracking Moment (b) Transformed Moment of Inertia. (c) Tension Stress of Concrete. (d) Transformed Compression Steel Stress. (e) Actual Tension Steel Stress. (f) Compression Force in the Concrete due to bending. (g) Total Tension Force of the reinforced concrete due to bending. 90 mm 20 mm 190 mm 70 mm 40 mm 3- Ø25 390 mm 40 mm 4- 020 70 mm 130 mm90 mm'
Asiacell lI. HW 2, M... Design the Beam AB Below by using Working Stress Method ; A 13.3 kN/m B for -4.8 m Dead Load, D.L = 10.7kN/m Live Load, L.L = 13.3 kN/m The allowable compressive stress of the concrete, fc = 11 N/mm² Allowable tensile stress in steel, fs = 150 N/mm? Modulus of elasticity of steel, Es = 260000 Mpa Modulus of elasticity of Concrete, Ec = 23000 Mpa Beam Width, b = 350 mm
1.2m 10 cm O 7cm -7cm O This concrete beam has four A-35 steel rods of one centimeter diameter and a square cross section. It experiences a compressive axial load of 200kN. You must calculate the stresses developed in the two components in the figure.
ASAP DONT REJECT ME, I'LL GIVE UPVOTE THANK YOUU Solve the basic development lengths in tension for the following deformed bars embedded in normal-weight concrete. State if you have assumptions. (a) 12mm bar dia; 32 mm bar dia. fy = 41.4 MPa fy = 413.7 MPa (b) 44mm bar dia; 57 mm bar dia. f c = 28 MPa fy = 552 MPa
L (m)=2.8 h (mm)=375 hs (mm)=325 b (mm)=275 (Ơst)allow (MPa)=150 (Ơconc)allow (MPa)= 18
A concrete beam of length 5.5m is built monolithically with the slab. Originally, the beam has a width of 300mm and effective depth of 400mm. If the flange of the slab is 150mm and the total area tension steel bars is 500 sq.cm., determine the design capacity of the beam structure. The concrete has a compressive strength of 25 MPa, steels' yield strength is 420 MPa. and the beam's clear span from its adjacent beams is 2.15m.
"Q1.16-.A rectangular beam has dimensions of 270 mm by 670 mm with an effective depth of 620 mm and is reinforced with 5- 20 mm ø. Concrete cover is 50 mm. The concrete cylinder strength f'c = 30.7 MPa and the tensile strength in bending is the modulus of rupture. The yield point of the steel is 449.5 MPa. The beam carries a bending moment of 67 kN-m. Use transformed section method to answer the following: (1) Compute the concrete compression stress at the top, (2) Compute the concrete tension stress at the bottom, (3) Compute the stress in the steel. (4) Assess the adequacy of the beam design." Use the editor to format your answer width, b ... effective depth, d total depth, h
REINFORCEB=(335mm)H=(435mm)
Assume straight line instead of parabola for stress-strain curve of concrete as follows and partial factor of safety as 1.0. 0.002 0.67 0.0035 Strain A rectangular under-reinforced concrete section of 300mm width and 500mm effective depth is reinforced with 3 bars of grade Fe 415, each of 16m diameter. Concrete mix is M20. The depth of the neutral axis from the compression fibre is