Assignment(1):- QI-For the rectangular reinforced concrete section shown in fig(1) .Answer the following:- Calculate the moment capacity of the section, so that the allowable stress in steel and concrete not exceed to 0.5fy and 0.45fe respectively? (neglect the steel in compression)? Use d=420 mm f=25Mpa, fy=420Mpa 3aYear- 2021 3#16 Fig.(1) #10 500mm 3#25 280mm

Assignment(1):- QI-For the rectangular reinforced concrete section shown in fig(1) .Answer the following:- Calculate the moment capacity of the section, so that the allowable stress in steel and concrete not exceed to 0.5fy and 0.45fe respectively? (neglect the steel in compression)? Use d=420 mm f=25Mpa, fy=420Mpa 3aYear- 2021 3#16 Fig.(1) #10 500mm 3#25 280mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

determine the minimum thickness of the steel bar. answer set c only
The aluminum W 310 x 202 (wide flange) column is subjected to an eccentric axial load P as shown. The maximum compressive stress in the column is given by the so-called secant formula: where --- [¹ + ( √5)] ec o 1+ sec max E ō = P/A = average stress A = 25800 mm² = cross-sectional area of the column e = 85 mm = eccentricity of the load c = 170 mm = half depth of the column r = 142 mm = radius of gyration of the cross section L = 7100 mm = length of the column E = 71 x 10⁹ Pa = modulus of elasticity Determine the maximum load P that the column can carry if the maximum stress is not to exceed 120 × 10^6 Pa. Terminate the computation when Σa < 0.0005%.
Question # 3: A cast iron beam is of 1-section as shown in Figure below. The beam is simply supported on a span of 5 metres. If the tensile stress is not to exceed 20 N/mm², find the safe uniformly load which the beam can carry. Find also the maximum compressive stress. 40 mm 20 mm 200 mm 80 mm 20 mm 160 mm. T
I need the answer quickly
A simply supported beam carries a concentrated load at the center which fluctuates from a value of W to 4 W. The span of the beam is 470 mm and its cross-section is circular with a diameter of 57 mm. Take ultimate stress of beam material as 683 MPa, Yield stress as 0.55 times ultimate stress and the endurance strength as 0.45 times the value of ultimate stress and take a factor of safety of 1.5. Calculate the maximum value of "W", if the variable stress induced in the beam is 109 N/mm?. Using Goodman relation calculate the value of mean stress in N/mm?. **Note: Please upload your handwritten working/solution to the link provided. Maximum Bending Moment Minimum Bending Moment Mean Bending Moment Variable Bending Moment Section Modulus, Z mm3 The value of Load "W". in N The value of Mean stress using Goodman relation ..
axial compressive force P. If the stress on steel snugly fitted on a solid steel rod of 20 mm A tube of aluminium of 40 mm external diameter and 20 mm internal diameter diameter. The composite bar is subjected to a bar is 70 N/mm", the stress in the aluminium tube and corresponding value of P will be: E for steel: 2 x 10 N/mm and E for aluminium 7 x 10ʻ N/mm')
Pls answer as indian code practice
I need a quick solution within 15 minutes With put a happy emoji at the end my best wishes Hamoudi
Show full solution
A rectangle column 500 mm x200 mm in cross-section is subjected to a compression load 1000 KN, the stress on the column is: a. 30 MPa b. 10 MPa C. 50 MPa d. 20 MPa
Question (3). Design Exercise (Selecting initial dimensions) A steel cross section of a bridge deck is shown in Figure 3. The cross section is subjected to a maximum bending moment of 43810 kNm. The length L is 4m. Available plate thicknesses (t) are 20 mm, 22 mm and 25 mm. The yield strength () is 355 MPa. Determine the initial dimensions of b and Cw, which can be used for detailed design of the bridge deck. Assume failure of the cross section mainly governs by in-plane bending. State all other assumptions made during this calculations. 60° 2b Ma