The cross section shown is for the fixed support of a propped beam that carries anallowable ultimate moment of 60 kN-m. The concrete is lightweight consisting of alightweight coarse aggregate and a mixture of a lightweight and normal weight fineaggregate. The total volume of fine aggregate is 15 m3 and 7m3 of it are lightweight.Determine the following if the compressive strength of the concrete is 25 MPa, fy=420 MPaand the weight of the concrete is 1600 kg/m3:(a) Cracking Moment(b) Transformed Moment of Inertia.(c) Tension Stress of Concrete.(d) Transformed Compression Steel Stress.(e) Actual Tension Steel Stress.(f) Compression Force in the Concrete due to bending.(g) Total Tension Force of the reinforced concrete due to bending.90 mm 20 mm190 mm70 mm40 mm3- Ø25390 mm40 mm4- 02070 mm130 mm90 mm'

Solution (sand and stone). The concrete glue is the "stick" which ties the particles in the total…

Answered: owing if the compressive strengt the…

owing if the compressive strengt the concrete is 1600 kg/m³: oment Moment of Inertia. ss of Concrete. Compression Steel Stress.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The concrete in the core of a spiral column is sub- jected to a uniform confining stress o, of 680 psi. What will the compressive strength o be? The un- confined uniaxial compressive strength is 5000 psi.
Use f'c = 30 MPa and fy = 415 MPa. The unit weight of concrete is 24 kN/m³ . The floor of a cantilever floor system is made up of a 150mm thick concrete slab (cast monolithically with beam) and the beams have widths of 300 mm, a total depth of 560 mm, and are to be reinforced with 5-Ø28 mm bars. The center-to-center spacing of beams is 4 m. The cantilever floor system is also built using 4m cantilever reinforced beams as supports. a) Find the maximum service live load (kPa) that the current floor design can support. b) Suppose that the floor will need to carry a superimposed service dead load of 2 kPa and service live load of 7.2 kPa, will the existing floor design be adequate? If not, redesign the beams (find the appropriate number of Ø28-mm rebars and provide a final sketch). Use cc = 40 mm, stirrup diameter of 10 mm, and nominal maximum aggregate size of 20 mm.
A rectangular cantilever beam has a width of 250mm and an effective depth of 480mm. It is reinforced with 7-25mm bars. The beam is carrying a uniformly distributed dead load of 15kN/m. The compressive strength of the concrete is 21MPa and the yield strength of the steel is 415MPa. The depth of the concrete stress block is?
Plz
The end block of a post-tensioned beam is 100 mm x 150 mm. A prestressing cable consisting of 7 wires of 6 mm dia strand and stressed to 800 MPa has to be anchored at the center of the block. The anchorage plate is 75 mm x 75 mm. If the concrete mix is M45 and the permissible bending stress in M. S. steel plate is 165 MPa, determine the thickness of the anchorage plate.
Problem- A doubly reinforced rectangular concrete beam has a width of 30mm and an effective depth of 500 mm. The beam is reinforced with 2200 mm² of steel in tension and 628 mm² of steel in compression. The effective cover for compression steel is 50 mm. Assume that both tension and compression steel yield. The grades of concrete and steel used are M20 and Fe250, respectively. The stress block parameters (rounded off to first two decimal places) for concrete shall be as per IS 456 : 2000. Find the depth of neutral axis.
A cast iron 3m long is completely filled with concrete and used as a vertical strut. If the externaldiameter of the tube is 450mm and the wall is 35mm thick, determine the maximum compressiveload the composite strut can support if the stress in the concrete is not 2N/mm2? By how muchshould the strut shorten under this load? For cast iron EA= 100GN/m2 and for the concrete EB=10GN/m2?
Determine the cracking moment (KN/M) and the compressive stress felt by concrete (MPa). Show your step by step answer with solution
PROBLEM TO SOLVE: 600 mm 400 mm 6-25mm diam. 90 mm Using fc' = 28 MPa, Mmax = +320 kNm Determine the following: a. Cracking Moment (kNm) b. Compressive Stress felt by concrete (MPa) c. Tension Stress felt by the tension bars (MPa) d. Moment of Inertia under critical condition e. Demand Capacity Ratio of Concrete under Compression Stress f. Compression force on concrete (kN) g. Distance of the compression concrete force from the neutral axis (mm)
Pre-stressed.
2. Tensile strength of concrete is about: (20-35)% of compressive strength (45-70)% of compressive strength None of the above. Tension controlled section Balanced section Compression-controlled section 4- The reduction factor (0) is equal to 0.9 if the: Es 2 Ety + 0.003 Es S Ety + 0.003 Es Ety 5- The design method which use the factored loads is - Working stress method - Ultimate design Method - None of above 6- If p< Po therefore the section is - Under reinforced - Over reinforced - None of above
If column AB is made from high strength pre-castconcrete and reinforced with four 20 mm diameter A-36steel rods, determine the maximum allowable floorloadings P. The allowable normal stress for the highstrength concrete and the steel are (ϭallow)con = 18 MPaand (ϭallow)st= 170 MPa, respectively.