Q- The width of the expansion joint is 20mm in a cement concrete pavement. The laying temperature is 20 °C and the maximum slab temperature in summer is 60 °C. The coefficient of thermal expansion of concrete is 10 x 10-6 mm, m/mm/ °C and the joint filler compresses upto 50% of the thickness. Find the spacing between expansion joints.

Q- The width of the expansion joint is 20mm in a cement concrete pavement. The laying temperature is 20 °C and the maximum slab temperature in summer is 60 °C. The coefficient of thermal expansion of concrete is 10 x 10-6 mm, m/mm/ °C and the joint filler compresses upto 50% of the thickness. Find the spacing between expansion joints.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Exp.joint
Internal diameter and depth of cylindrical steel cup are mm and mm in Aggregate Impact Value test. А. 204 mm, 100 mm В. 61mm, 25 mm C. 150 mm, 75 mm D. 102 mm, 50 mm B.
I need the answer as soon as possible
Determine the permanent deformation after 2 hours show all work
Standard deviation is 3.6 MPa
Use ACI method .
Cracking Analysis of Reinforced Concrete ANSWER A. TO G. COMPLETE SOLUTIONS -positive bending moment = +200KNm -draw transformation of areas -draw strain and stress diagram
Q. Using the British methods, design a concrete mix to bear an average compressive strength of 35 MPa at 28 days, to cast a room slab with the following dimensions (5 width x 4 length x 0.2 depth m) and 200 mm space distance of reinforcement. Consider the following properties: o Cement used is type I Portland cement ® Required slump = 30 — 60 mm o Coarse aggregate: ® Crushed rocks * Maximum size of 40 mm, e The fine aggregate: * Crushed rocks = Falls in zone 3 o Assume zone A for figure 1 o AssumeK = 1.64
An aluminum pipe is filled in polymer concrete is subjected to a pure compressive force as shown in the figure below. Determine the factor of safety against compressive stress acting on the column. The pipe has an outer diameter of 60 mm and inner diameter of 50 mm. The aluminum and the polymer concrete have the following material properties: Young's modulus: Eal = 70 GPa (aluminum). Ecr = 10 GPa (polymer concrete). Yield compressive strength: Sy-al = 150 MPa (aluminum), Sy-cr= 80 MPa (polymer concrete). 100 kN 500 mm Select one O FS = 6.4 FS= 1.3 o FS =1.1 O FS =1.7 OFS=50
Use ACI method.
Design the concrete mix according to the following conditions:Design Environment• Building beamo Required design strength = 27.6 MPao Minimum dimension = 150 mmo Minimum space between rebar = 40 mmo Minimum cover over rebar = 40 mmo Statistical data indicate a standard deviation of compressive strengthof 2.1 MPa is expected (more than 30 samples).• Only air entrainer is allowed.• Moderate Sulphate exposure.• Available Materialso Air entrainer:▪ Manufacture specification 6.3 mL/1% air/100 kg cement.o Coarse aggregate:▪ 19 mm nominal maximum size▪ River gravel (rounded)▪ Bulk oven-dry specific gravity = 2.55▪ Absorption = 3.6▪ Oven-dry rodded density = 1761 kg/m3▪ Moisture content = 2.5o Fine aggregate:▪ Natural sand▪ Bulk oven-dry specific gravity = 2.659▪ Absorption = 0.5▪ Moisture content = 2▪ Fineness modulus = 2.47o Cement▪ Type II (Moderate Sulphate Resistant)▪ Specific Gravity = 3.15Based on this information, find the following and summarize the findings in a table d) The amount…
Group B: Design a concrete mix to implement a concrete wall (exposed to sever conditions moisture and sea water or sulphates) with design compressive strength 40 MPa, a standard deviation equals to 4 and the percentage expected less than minimum strength is 5%. Sulphate Resisting Portland Cement is used. The maximum size of an angular aggregate is 40 mm with apparent density 1500 kg/m3. The available fine aggregate has fineness modulus 2.4 an air entraining agent has been used in the mix.