The building wall consists of 12-in. clay brick. In the interior, the wall ismade from 2 x 4 wood studs, plastered on one side. If the wall is 4 fthigh.Let 2x4woodstudsplasteredoneside =12 in. claybrick = 115ps fh= 12psfDetermine the load in psf of length of that the wall exerts on the floor.[Select][Select]548 psf364 psf204 psf508 psf

Answered: Image /qna-images/answer/be15a229-c312-449f-a112-2a20229c9584.jpg

The building wall consists of 12-in. clay brick. In the interior, the wall is made from 2 x 4 wood studs, plastered on one side. If the wall is 4 ft high. Let 2x4woodstudsplasteredoneside = 12ps f 12 in. claybrick = 115ps f h Determine the load in psf of length of that the wall exerts on the floor. [Select] [Select] 548 psf 364 psf 204 psf 508 psf

The building wall consists of 12-in. clay brick. In the interior, the wall is made from 2 x 4 wood studs, plastered on one side. If the wall is 4 ft high. Let 2x4woodstudsplasteredoneside = 12ps f 12 in. claybrick = 115ps f h Determine the load in psf of length of that the wall exerts on the floor. [Select] [Select] 548 psf 364 psf 204 psf 508 psf

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

450 mm 750 mm Ce = 40 mm db = 25 mm fe' = 28 Mpa fy = 414 Mpa Mu max = 1000 KN-m a. determine the actual depth of compression block b. determine the area of tension reinforcement c. determine the area of compression reinforcement
A rectangular concrete beam has a width of 300mm and an effective depth of 550mm. The beam issimply supported over a span of 6m and is used to carry a uniform dead load of 25 kN/m and a uniformlive load of 40 kN/m. Assume fc’ = 21 MPa and fy = 312 MPa. Compression reinforcement, ifnecessary, shall be placed at a depth 80 mm from the outermost compression concrete. Used loadcombination of 1.4DL + 1.7LL. 4. Determine the required compression steel area in square millimeters.5. Determine the required number of 25-mm compression bars.
Pb- DCS.
Reinforce Concrete Design Determine the design moment capacity of the reinforced concrete beam shown inFigure 1(a) if it is reinforced with 4-28-mm diameter in tension and 2- 16-mmdiameter in compression. Use f’c = 21 MPa, fy = 276 MPa and effective cover of 50 mm for top and bottom bars.Assume the load W to be ultimate. Neglect weight of beam.
ll中国移动 4G PN © 11:50 PM 75% 4 A spiral column with the diameter of 500 mm has the effective height of lo-4.0 m. The axial compressive strength of the concrete is f. - 14.3 N/ mm. The longitudinal steel bars are 6 22 with the yield strength ofS, - 360 N/mm. The spirals are 10@50 with the yield strength of f,- 270 N/ mm². If the concrete cover is 30 mm thick, determine the ultimate compressive capacity of the column.
Need Complete an elaborate solution Design a square base plate to support 12 mm thick pipe column with an inside diameter of 400 mm. The base plate minimum dimension is 500 mm. To design plate thickness, convert the circular perimeter of the pipe into an equivalent square with an area equal to the original circle. The loads are PDL = 700 kN and PLL =320 kN. Assume that the pipe is to rest on a very wide slab. Use A-36 steel and concrete fc’ = 25MPa and ASD.
Use any method ans is 697.5lb
A 15 x 25 in. column is reinforced with four No. 9 (No. 29) bars, one in each corner as shown in Figure (a). The concrete cylinder strength is f. = 4000 psi and the steel yield strength is 60000 psi. Determine the axial load strength for zero eccentricity without subtraction of the concrete displaced by the steel, as well as with subtraction of the concrete displaced by the steel. E=0.003, E,-29000. Imperial Metric bar Linear Mass Density Nominal diameter Nominal area 25" bar size size (soft) Ib (in) (mm) (in') (mm") 2.5" -2.5" 0.250 - % 6.35 0.05 32 0.375 = % 9.53 0.11 71 0.500 = 4 12.7 0.20 129 0.625 = % 15.9 0.31 200 0.750 = % 19.1 0.44 284 0.875 = % 222 0.60 387 1.000 = % 25.4 0.79 510 1.126 - % 28.7 1.00 645 1.270- 1% 32.3 1.27 819 No.6 0.167 0.249 3 No. 10 0.376 0.560 #4 No. 13 0.668 0.994 Pn #5 No. 16 1.043 1.552 15" No. 19 1.502 2.235 #7 No.22 2.044 3.042 #8 No 25 2 670 3.973 As No 29 3.400 5.060 A's #10 No 32 4.303 6.404 e varies #11 No.36 5.313 7.907 1.410- 35.8 1.56 1.006…
pls help! write the solutions completely and legibly. upvote will be given! MECHANICS OF DEFORMABLE BODIES
A rectangular reinforced concrete beam exposed to earth has a total depth of 600 mm and a width o 350 mm. It is reinforced with 3-22 mm diameter bar (fy' = 315 MPa) in compression and 5 - 25 mm diameter bar in tension (fy= 345 MPа). fc' 3D 28 MPа a. determine the effective depth of the beam b. determine the depth of compression block C. check if steel yields for both tension and compression reinforcement d. determine the ultimate capacity of the beam %3D
Estimate the flexural (hogging and sagging)
Use any method correct and is 697.5lb