Question 1 2.5 N/m 2.5 N/m F Using the Approximate Method for Vertical Load, produce the shear force and bending moment diagram for the frame below. The height of each storey is 5 m. 2.5 N/m 2.5 N/m B H E Using the information given and calculate what will be the axial loads on 5 m 8 m G the columns.

Question 1 2.5 N/m 2.5 N/m F Using the Approximate Method for Vertical Load, produce the shear force and bending moment diagram for the frame below. The height of each storey is 5 m. 2.5 N/m 2.5 N/m B H E Using the information given and calculate what will be the axial loads on 5 m 8 m G the columns.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

concrete : C20 steel: S420 h=550 mm b=350mm steel rebars : 5Φ18
Calculate the ultimate axial load capacity of a round spiral column having a diameter of 450mm reinforced with six 25mm bars having fy=276 MPa. Assume fc’=34MPa.
calculate the euler buckling load for a pin-connected steel pipe column. use a= 8.4 in^2, r= 2.94 in, and the following lengths: (a) 50 ft ( b) 35 ft (c) 20 ft (d) 15ft. the proportional limit is 34,000psi
2. A uniformly distributed load of 54 Ib/ft is carried by a simply supported beam span. The beam is a hollow rectangular section, having a width, b = 10.5 inches, height, h = 11.2 inches and constant wall thickness of 0.9 inches. Determine the maximum length of the beam in feet if the shearing stress is limited to 82 psi. Assume the load acts over the entire length of the beam.
For the simple beam shown below, draw the factored shear-force envelope, and design stirrups using fc’ = 5000 psi and fyt = 60,000 psi. Use the approximate method. (Beam weight is included in the dead load)
A simply supported beam with overhang is shown. 4 in. 0.375 in. 1,200 lb 0.375 in. 450 1Ь/л 8 in. 0.375 in. |C 14 t 6 ft Determine the maximum flexural stress in psi. (Numerical absolute answer only without units in 3 decimal places)
Please I need help to calculate axil force due to dead and live load in three different columns A1, A2, C3 2) Design column A2 using reinforced concrete and steel. DL= 6 LL=3.5
A channel shape is used to support the loads on the beam below. The dimensions of the shape of the beam is also given. Consider the entire 12-ft length of the beam and determine the stress at the top and bottom of the beam.
SHOW COMPLETE SOLUTION AND DRAW THE FBD.
The floor system consists of a 6 in. thick reinforced concrete slab weighing 150 Ib/ft³. The weight of floor beams, utilities, and suspended ceiling from the floor is equal to 15 Ib/ft?. Using the tributary area method, (1) compute the floor dead loads supported by columns A1 and B2 in the figure, (2) If column D2 and girder 2CD were omitted, determine the support load at column D1 and C2. B 20 - 22- - 22' TI- I- 9' 18' 9' 9' 18' 9 2 I- 10 10' 11 11' 11 11
Figure below shows the partial steel structure floor framing plan of a hospital building. Assuming a total DL of 100 psf and an average LL 60 psf. 1. For Beam B1: Using LRFD load combinations: a. Calculate the corresponding factored loads, Wu (klf) b. Draw the shear force diagram and calculate the maximum factored shear, Vu (Demand). c. Draw the bending moment diagram and calculate the maximum factored moment, Mu (Demand). 2. For Girder G1: Using LRFD load combinations: a. Calculate the corresponding factored loads, Wu (klf) b. Draw the shear force diagram and calculate the maximum factored shear, Vu (Demand). c. Draw the bending moment diagram and calculate the maximum factored moment, Mu (Demand).