The floor system consists of a 6 in. thick reinforced concrete slab weighing 150 Ib/ft³. The weight of floor beams, utilities, and suspended ceiling from the floor is equal to 15 lb/ft?. Using the tributary area method, (1) compute the floor dead

The floor system consists of a 6 in. thick reinforced concrete slab weighing 150 Ib/ft³. The weight of floor beams, utilities, and suspended ceiling from the floor is equal to 15 lb/ft?. Using the tributary area method, (1) compute the floor dead

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1. A reinforced concrete column 400 mm in diameter is designed to carry an axial compressive load of…

Q: zweeks 99 3. From the followin quired for the colu concrete. Dia = 42 12 pcs. Octagonạl Colum

Q: 01/ The given data of a rectangular tank are: The bottom is hinged and top is free, a-4 m, b-12 m,…

A: The minimum wall thickness for flexural requirement: Thickness of tank is adopted based on the…

Q: The submerged brick is balanced by a 3.13kg mass on the beam scale. What is the specific weight of…

A: We can calculate the specific weight of the brick by first calculating the weight of the brick by…

Q: A 1.2-m length of a steel pipe 500 kN of 200-mm outer diameter and 12-mm wall thickness is used as a…

A: Given data in question Load Length Outer diameter Thickness Poissons ratio Elasticity modulus To…

Q: A 30m tape is supported only at its ends and under a steady pull of 8kg. If the tape weighs 0.91 kg,…

A: Introduction- The Tape correction(s) in surveying refers to the process of adjusting measurements…

Q: The gate AB is 4.60 m long and 2.4 m wide perpendicular to the paper and is hinged at A with a stop…

Q: Q3. A circular concrete column with a height of 3 m made of 8 bars with diameter of 22 mm. determine…

Q: 2. The second floor of a light manufacturing building is constructed from a 125-mm-thick stone…

Q: The floor system shown is made of concrete (self-weight of concrete is 25kN/m³). Its thickness is t.…

A: Given Data Floor system made of concrete Self weight of concrete = 25 kN/m3 D=2 Thickness of slab =…

Q: A rectangular block is 132 mm long in the X direction, 76 mm wide in the Y direction, and 65 mm…

Q: a. weight "WFc" of the frustum of the cone in kN b. radius "R," of the frustum in meters at the…

Q: Draw shear force diagram

A: Support reaction : Apply equilibrium condition ∑MB=01 k=1000…

Q: Example 4.2:A wooden block of s= 0.7 and having if floating in water, determine the volume of concre…

A: GIVEN DATA:-⇒S= 0.7⇒ρw'=700 kg/m3⇒Size= 2×0.5×0.25 m3⇒γ= 25 KN/m3⇒ρw= 1000 kg/m3⇒g= 9.81≈ 10 m/s2

Q: You are assigned to a project for the construction of a new tunnel. The tunnel will be 31 feet in…

A: Assuming that the supports are continuous throughout the length of the tunnel and the length of…

Q: 2. The second floor of a light manufacturing building is constructed from a 125-mm-thick stone…

A: Thickness of concrete slab(tslab) = 125 mm = 0.125 mThickness of cinder concrete (tcinder) = 100 mm…

Q: The following shows a schematic section of a three-story reinforced concrete building. The building…

A: To Determine - The total weight of the building

Q: A floor slab 100 mm thick is cast monollthically with beams 250 mm wide 450 mm deep spaced 1.2 m on…

A: Given:- The thickness of the slab = 100 mm The width of the beam = 250 mm The depth of the beam =…

Q: Urgent, need correct answer as soon as possible with complete solution. Box final answer in 4…

Q: The uniform concrete slab has a mass of 2900 kg. The slab is held in the horizontal plane by three…

Q: A rectangular block is 129 mm long in the X direction, 100 mm wide in the Y direction, and 56 mm…

Q: (a) What is the value of the Reynolds number? (b) What is the magnitude of the pipe wall roughness?

A: The values given in the question are as follows: Water flow rate(Q)=700 gpm or 2695 in3/sec Diameter…

Q: A trough full of liquid weighing 50 lb/ft3, has its cross-section in the shape of an isosceles…

Q: Water flow through a 100 mm diameter pipe with a velocity of 0.015 m/sec. If the kinematic viscosity…

A: Diameter of pipe = 100 mmkinematic viscosiy of water = 1.13 X 10-6Velocity of water = 0.015 m/secTo…

Q: A concrete wall shaped as an "inverted T" is used to prevent flooding. Calculate the force F that…

Q: rcular log 6m long has a radius of 1.40m. If the specific gravity of the log is 0.52 and if placed…

Q: A 50 meter steel tape is suspended in the air between a transit and a vertical rod which is placed…

A: If the sag correction is neglected there will be only slope correction:cslope=l1-cosθθ=1°30'

Q: Derive the general expression for Shear Stress and velocity istribution for laminar flow in pipe.…

A: To derive for laminar flow for pipe

Q: Question 1 A concrete slab has a dead load of 6 kPa and live load 5 kPa, and has support columns…

A: Solution: Given: DL = 5 kN/m2 LL = 6 kN/m2 span = 3 m

Q: 00 mm thick is cast monolithically with beams 250 mm wide on centers, on simple supports over a span…

A: According to given data Floor slab 100 mm thick casted monolithicallywith beams 250 mm wide and 450…

Q: What is the roughness coefficient of a steel pipe with a length of 100 meters if the observed head…

Q: 3. From the following figure, find the concrete materials re- quired for the columns 9.00 meters…

Q: For the reinforced concrete floor shown in the Figure below, design the slab to carry service live…

A: Solution: Given: LL = 6 kN/m2 fc = 25 MPa fy = 420 MPa concrete density = 24 kN/m3 Plaster density =…

Q: A reinforced concrete column 200 mm in diameter is designed to carry an axial compressive load of…

Q: A block of wood 50cm in diameter with s = 0.95 is immersed in a liquid with s = 1.05. Determine the…

Q: Consider the following load condition, determine the magnitude of Vmax. 400 lb/ft 600 lb-ft 15 ft B

Concept explainers

Design of structures using FEA

An arrangement, in which various members are interconnected with their constrained relative motion, the whole arrangement is then known as a structure. The degree of freedom of such a structure is zero. In such a structure, the load can act throughout the length of the structure or at the joints.

Question

The floor system consists of a 6 in. thick reinforced concrete slab weighing 150
Ib/ft³. The weight of floor beams, utilities, and suspended ceiling from the floor is
equal to 15 Ib/ft?. Using the tributary area method, (1) compute the floor dead
loads supported by columns A1 and B2 in the figure, (2) If column D2 and girder
2CD were omitted, determine the support load at column D1 and C2.
B
20
- 22-
- 22'
TI-
I-
9'
18'
9'
9'
18'
9
2
I-
10 10'
11 11'
11 11

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Solution:-

Step 2 Solution:-

Step 3 Solution:-

Step 4 Answer:-

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please solve the problem carefully. Handwritten solution recommended.
Figure A 4.5 m Wo B. 1 of 1 1.5 m C Part A Determine the largest intensity wo of the distributed load that the beam can support if the beam can withstand a maximum bending moment of Mmax = 12 kNm and a maximum shear force of Vmax = 80 kN. (Figure 1) Express your answer with the appropriate units. Wo = Submit ☐ O µA Value Request Answer Return to Assignment Units Provide Feedback
solution w/fbd
Situation 5. A floor slab 100 mm thick is cast monolithically with beams 300 mm wide 500 mm deep spaced 1.5 m on centers, on simple supports over a span of 6.0 m. The floor supports a superimposed service dead load of 1.77 kPa and service live load of 4.8 kPa. Using f'c 21 MPa, long bar fy = 415 MPa, calculate: 12. Factored uniform load on a typical interior beam in kN/m using load factors of 1.2 for dead load and 1.6 for live load. A. 18.68 B. 17.35 A. 1,800 B. 1,500 C. D. 13. Using a T-beam geometry formed from monolithic construction, determine the effective flange width of a typical interior beam in mm. 22.48 25.78 A. 495 B. 560 C. 1,200 D. 1,900 14. Using a T-beam geometry, determine the required area in mm² of 16-mm-dia. flexure bars for maximum ultimate bending. C. D. 620 448
2. A CUBICAL FLOAT 1.2m ON A SIDE, WEIGHS 182kg AND IS ANCHORDED BY ME NS OF A CONCRETE IS TAUT, 22.5cm OF FLOAT ARE SUBMERGED. WHAT RISE IN THE WATER LEVEL WILL LIFT THE CONCRETE OFF THE BOTTOM ? CONCRETE WEIGHS = 2400 kg/m³. 1.2 H 86824 _WS
Civil engineering
An engineer proposes as a solution to the problem of the dam, to reinforce it according to the figure shown, but now the critical height h of the water level must be determined, which would make the indicated concrete reinforcement on the verge of overturning due to the water pressure. The density of the concrete 2.40 Mg/m^3, H=18m and d= 6m. Hints: use typical values of water, consider one meter width of the dam to then generalize and don't forget point A.
REINFORCED CONCRETE DESIGN
A seawall made of concrete is shown. Determine its total volume and total weight if concrete weighs 150 lb/ft^3.
2) The flooring system shown is composed of slab panels measuring 20 X 25 ft in plan, supported by shallow column-line beams, as shown in the figure. The slab is pre-cast and resting on the beams. The panels carry a service live load of 144 psf in addition to the self-weight of the floor. a) Calculate the factored load on beam CD as per the tributary area shown. Assume a slab thickness of 7 in and the density of the concrete used to be 150 pcf. Use the load combinations from the ASCE 7-10 load combinations for Strength Design (2.3.2). b) Sketch the bending moment diagram (BMD) for the beam using the factored load calculated in step (a). c) Calculate Mu for the trapezoidal load distribution. d) Design a reinforced concrete beam using a rectangular section to carry the Mu calculated in step (c). You can use design guides, but show clear steps. Use concrete with fc'=4000 psi and steel with fy = 60000 psi.
Mechanics of deformable bodies. Two decimal places.
Provided is the question along with some notes taken in the lecture, i am not sure if i am correst so if you could do some workings out for me that would be great , thank you.