column Problem 2. The floor system of a gymnasium consists of a 130-mm- thick concrete slab resting on four steel beams (A = 9,100 mm2) that, in turn, are supported by two steel girders (A = 25,600 mm2), as shown in Figure. Determine the dead loads acting on beam BF and girder AD. 130 mm 10 m concrete slab H G 3 at 5 m- 15 m

column Problem 2. The floor system of a gymnasium consists of a 130-mm- thick concrete slab resting on four steel beams (A = 9,100 mm2) that, in turn, are supported by two steel girders (A = 25,600 mm2), as shown in Figure. Determine the dead loads acting on beam BF and girder AD. 130 mm 10 m concrete slab H G 3 at 5 m- 15 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2.1.Write the Equation and describe the style in the latitude of the structure
A steel pipe (D = 3.500 in.; d = 3.068 in.) supports a concentrated load of P = 617 lb as shown. The span length of the cantilever beam is L = 4 ft. Determine the magnitude of the maximum bending stress in the pipe. O 21.55 ksi O 13.81 ksi O 15.73 ksi O 24.04 ksi O 17.18 ksi L B P d Pipe cross section. D
The beam shown in figure carries a uniformly distributed load of w on overhang BC. The beam is constructed of a wood beam [E,=12 GPa] that is reinforced on its upper surface by a steel plate [E,-200 GPa] plate. Assume that the allowable bending stresses of the wood and the steel are o. = 9 MPa and o = 165 MPa, respectively. Determine the largest acceptable magnitude for distributed load w. [L = 4m, a = 1.25 m, b. =150 mm, d, =280 mm, b. = 230 mm, t, = 6 mm] IC
Example No.3: A simply supported beam shown in figure of 6.1 m span. It is reinforced with equivalent of four wires of 64.5 mm² each pretensioned to initial stress of 1103 MPa. Compute the total dead and live load moment that can be carried by the beam. Assume fc'= fci'-35 MPa, R=0.8. Assume all live loads are sustained. 200 mm 75 mm 32 mm 75 mm 32 mm 200 mm
Concrete T-beam has been reinforced by bonding a steel plate to its web asshown below. The beam carries a uniformly distributed load of 40kN/m over a simply supported 8m span. Find the maximum deflection of the beam on the assumption that the concrete is fully operative in both tension and compression.(Est = 200kN/mm^2. Econc = 30kN/mm^2; central deflection due uniformly distributed load, total W acting on a simply supported beam of span L= 5WL^3/(384EI)) can someone please answer this question in detail who is confident in this topic with step-by-step calculations & sketch pls. I've asked this question twice now and I've gotten different answers each time so I'm at a bit of a loss. (DONT respond to this if you have already responded previously) Thank you
Situation. A flooring system consists of parallel I-beam sections spaced at 3 m. on centers simply supported over a span of 9 m. The beam supports a 200 mm thick concrete slab of ultimate strength f'c = 21 MPa. The flooring system is designed for as ceiling and floor load of 750 N/m². The properties of the I-beam sections are: A = 11,500 mm² d = 350 mm; tw = 10 mm bf = 250 mm; t = 16 mm lx = 266x106 mm4 ly = 45 x 106 mm4 fy = 248 MPal Wb = 90 kg/m fy = 248MPa If each beam is laterally braced by the concrete slab, calculate the allowable bending strength using safety factor of 1.67. Select the correct response: 175.17 248.79 235.94 394.03
Rectangular reinforced concrete beam section b = 40 cm, h = 60 cm, d = 53 cm, material strength fy = 4200 = 4200 kgf / cm^2, fc ' = 280 kgf/cm^2, beam section configuration #4 For closed stirrups @15 cm, the net cover is 4 cm, and the beam section is subjected to a torque of Tu = Tcr. Q: What is the ultimate shear load value Vu that the beam section can bear. Among them, Tcr is the cracking torque of the beam section, #4 steel bar (db=1.27 cm, Ab=1.267 cm^2).
The steel framework shown below is used to support the reinforced concrete slab (unit weight of concrete =23.6KN/m3) that is used for an office use (minimum live load = 2.4KPa). The slab is 150 mm thick. Use a=3m, b=5m. Neglect the self-weight of the beam and girder. Assume all beams and girders have simple supports. NSCP 2015 Load factors: 1.2DL & 1.6LL. Calculate the total ultimate/factored liveload in Kilo Pascals? Express your answer in 2 decimal places
the floor framing plan of a reinforced concrete building. All beams are 300 mm x 600 mm. The properties are as follows: slab thickness = 100 mm; super imposed dead load = 3 kPa; live load = 4.8 kPa; concrete unit weight = 24 kN/m3. The columns at E and H are deleted thus girder BEHK alone supports beam DEF at E and beam GHI at H. Calculate the uniformly distributed service dead load at beam DEF in kN/m Calculate the uniformly distributed service live load at beam DEF in kN/m.
A steel pad supporting heavy machinery rests on four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression is 400 MPa. The total load P that may be supported by the pad is 890 kN. Using a factor of safety 3.0 with respect to ultimate strength, determine the outer diameter of the pier (in mm) if the thickness of the cross section is 10 mm. mm
A reinforced concrete beam as shown in the figure below has a flange width of350mm, flange thickness of 120mm, and an effective depth of 600 mm. It is reinforced with 3-32 mm ∅ at the bottom. If fc’ = 28MPa, and fy = 275 MPa, determine the following:a. Balance steel ratiob. Depth of compression block.c. Moment capacity of the beam.
4