Q1) A uniform T-section beam is 100 mm wide and 150 mm deep with a flange thickness of 25mm and a web thickness of 12 mm. If the limiting bending stresses for the material of the beam are 80 MN/m2 in compression and 160 MN/m2 in tension, find the maximum varying load (w) applied on the beam shown in the figure.

Q1) A uniform T-section beam is 100 mm wide and 150 mm deep with a flange thickness of 25mm and a web thickness of 12 mm. If the limiting bending stresses for the material of the beam are 80 MN/m2 in compression and 160 MN/m2 in tension, find the maximum varying load (w) applied on the beam shown in the figure.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported beam carries a concentrated load at the center which fluctuates from a value of W to 4 W. The span of the beam is 470 mm and its cross-section is circular with a diameter of 57 mm. Take ultimate stress of beam material as 683 MPa, Yield stress as 0.55 times ultimate stress and the endurance strength as 0.45 times the value of ultimate stress and take a factor of safety of 1.5. Calculate the maximum value of "W", if the variable stress induced in the beam is 109 N/mm?. Using Goodman relation calculate the value of mean stress in N/mm?. **Note: Please upload your handwritten working/solution to the link provided. Maximum Bending Moment Minimum Bending Moment Mean Bending Moment Variable Bending Moment Section Modulus, Z mm3 The value of Load "W". in N The value of Mean stress using Goodman relation ..
The steel beam has the cross section shown. The beam length is L = 6.4 m, and the cross-sectional dimensions are d = 345 mm, by = 205 mm, t = 16 mm, and tw = 7 mm. Calculate the largest intensity of distributed load wo that can be supported by this beam if the allowable bending stress is 215 MPa. Answer: Wo Wo kN/m T₁₂ y
I. Problem Solving. Box your final answer. 1. Find the (a) maximum tensile and compressive bending stress in the wooden beam and (b) maximum shear stress in the shaded area of a wooden beam. 1 . 4kN 2kN 3kN 2m- A 1m 1m 2m 4m 3m 8m 5m 1m
Consider the following uniformly loaded simple beam. The beam has a span length L = 2.5 m, the load has a uniform intensity q = 3.8 kN/m, and the maximum bending stress o = 60 MPa. q = 3.8 kN/m L = 2.5 m The cross section of the beam is square, and the material is aluminum having modulus of elasticity E = 70 GPa. (Use the formulas of this example. Use available deflection formulas. All beams have constant flexural rigidity EI.) Calculate the maximum deflection 8, max: (Enter the magnitude in mm.) mm
with FBD please Complete solution thank you
Please help me solve this problem. Need it asap. Thank you.
A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at 3.4 from the support. (MPa) Properties: Beam width - 211 mm Beam height = 414 mm Pu 73.09 kN Span of the beam = 10 m Prestressing force = 509 kN eccentricity = 130 mm
A steel I-beam has a web that is 17inches tall and 0.19inches thick. If the max shear in the beam is 6kips, what is the approximate max shear stress in the beam in psi? Type your answer...
Is it possible to solve the question as soon as possible and with all the points?
Higdon
Problem 2 A) Draw the shear-force and bending-moment diagrams for the beam shown in the figure. B) For the composite section, aluminium [E = 70 GPa] bonded to a steel [E = 210 GPa), located at the maximum bending moment, determine: (1) the maximum bending stresses in the aluminium and steel bars. (2) the stress in the two materials at the joint where they are bonded together. 2m B 10kN/mm 4m C 2m Steel Aluminum 42 mm 20 mm 13 mun
6. A cantilever beam with cross section shown in Figure 4 and span of 3.6 m is subjected to concentrated load (P) at the free end. If the maximum allowable shearing stress equals to 4 MPa what is the maximum value of the load P can be applied. 200 mm 40 mm 100 mm H 20 mm