Answered: 4. The beam shown supports the load…

4. The beam shown supports the load shown, determine max flexural stress developed and 200mm the max beam shear developed in the beam 2000N 1m 1m 600N/m 4m 888 40mm 150mm 30mm OC €

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Design the shear reinforcement for the beam shown in figure below assuming it resists an ultimate shear force at distance d from the face of the support of 450 kN. The characteristic material strengths are fok= 25 N/mm²and fm = 500 N/mm² 450 kN d= 500 mm -4H25 b= 300 mm
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
Maximum allowable (safe) bending stress for a beam AB under a constant distributed load as shown in the figure.It is 40 MPa.a) What is the maximum value of the length (L) of the beam in this case?b) Draw the shear stress (τ) profile where the V (shear in section) force is greatest.Hint: You can specify several points in the section and calculate the shear stress for those points.
is strengthened by bolting two cover The wide-flange beam shown in Fig. plates 160 mm by 20 mm to the top and bottom flanges. If the maximum flexure stress is 140 MPa, compute the total force (a) in each cover plate and (b) in each flange. Neglect the weakening effect of the bolt holes. 160 mm 20 mm 20 mm 320 mm 20 mm €20 mm
At which point on the design P-M interaction diagram is the design flexural strength largest? O Pure compression Pure tension Balanced failure point (CCL limit) O TCL limit Beam condition (Pn = 0) %3D //img00.zhaopin.cm
Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
A steel cantilever beam 6 m in length is subjected to a concentrated load of 120 N acting at the free end of the bar. The cross section of the beam is shown below. deep. Determine the magnitude and location of the maximum tensile and compressive bending stresses in the beam. As usual, neglect the weight of the beam. 4mm 120 N 1mm 1mm 6mm 6m 1mm 4mm
a) Two bars of different size form a pin-connected frame that supports a Load 'P' at point A as shown in the Fig. 3. What safe load P (kN) can be applied if the allowable stress of 120 MPa is not to be exceeded? Assume buckling has been prevented. Allowable stress is based on a factor of safety of 2.0. Cross sectional area of the rods AB and AC are given in the adjacent table as per last digit of Roll number. What is the failure load? Last digit of Area of AB | Area of AC Roll No. 1, 2, 4 & 7 200 mm 230 mm“ 3, 6 & 8 160 mm- 190 mm² 5, 9 & 0 180 mm 210 mm 2400 1600 Fig. 3 b) Two square bars are of equal length but have different size as shown in Fig. 4. Compare the maximum stress in the two bars if they are to receive the same input of energy from axial load. Given, m = (2 + last digit of your roll number). 2a 5.x m.x Fig. 4 last digit of roll=1
SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum force F that can be applied to the plates. The allowable axial stress of each plate is 150 Мра. The allowable shear stress of each bolt is 50 MPa. The diameter of each bolt is 16 F F 150 mm F F mm. 50 mm 340 mm
QUESTION 6 A bar of uniform cross sectional area- 168.290 mm2 is fully fixed at supports A and B and subjected to axial loads P and F along its length applied in the directions shown LAB 6m, LBC-3m A B F If the value of P is 23kN and that of F is 13kN, determine the stress acting in member AB, identifying a compressive stress ( in N/mm2) as negative and tensile stress as positive. Present your answer to three decimal places.
2. Member AB shown in the figure supports a 5 N/mm uniformly distributed load and 4kN concentrated load as shown in the figure. Determine the position x of these loads so that the average tensile stress in the tie rod AC is equal to 90% of the compressive stress at the smooth support B. The rod has a diameter of 19 mm and the contact area at is 700mm². (Hint: quadratic formula) B A X 5 N/mm 4 kN 300mm B
For the beam shown in Figure (1), determine: a) The stresses in rods AB and BC. The cross-sectional area of rod AB is 155 mm2, and for BC is 200 mm?. b) The average shear stress in bolt at pin A. 1500 N S5 15 m 600 N/mt m- -3 m- Figure (1)