Example 2.2-A simply supported reinforced beam has a cross section with a width of 500mm and a depth of 750mm, and a span of 15m. It carries a deadload of 20kN/m and an occupancy load of 4.8kN/m. It also carries a deadload of 20kN and a live load of 5kN located at 8m from the left support. The beam is made of normal density concrete. Determine the maximum factored bending moment in the beam, Mr, due to the applied factored loads.

Example 2.2-A simply supported reinforced beam has a cross section with a width of 500mm and a depth of 750mm, and a span of 15m. It carries a deadload of 20kN/m and an occupancy load of 4.8kN/m. It also carries a deadload of 20kN and a live load of 5kN located at 8m from the left support. The beam is made of normal density concrete. Determine the maximum factored bending moment in the beam, Mr, due to the applied factored loads.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular concrete beam of cross section 100mm wide and 400mm deep is prestressed by a straight cable of span 6m, imposed load is 3.14kn/m, area is 36×10³mm²(Z=18×105mm³). Calculate working moment assuming the self weight of concrete as 24kn/m³?
-3m 3 m Determine the resultant equivalent load and resultant couple moment w1=4 kN w2=7.5 kN
Q4/ Compact the design bending strength to the reinforced concrete beam has a width b=300mm and effective depth d=525mm, fc-20, fy=300MPa. Suppose that the beam design to achieve a maximum bending according to code.
A 6m steel wire hanging on one end has a weight of W, it supports a load of 243 kN, determine the required diameter if the elongation would not exceed 1.69 mm, Assume E = 2 GPa.
Question :- The width of the beam is 250 mm and the overall deep 620 mm. It has three equal spans of 6.0 m each. The beam is arranged at 3.5 m from center to center, while the thickness of the slab is 200 mm. The imposed live load qk on the beam is 45 kN/m and the dead load gk inclusive of self-weight of the beam is 75 Kn/m. the characteristic strength of materials are feu = 30N/m², fy = 460N/mm² and f 250N/mm², Assume that the mild exposure for the beam and the nominal cover of 25 mm. Design the beam
a reinforced concrete column of 300mm dia contains 4 bars of 22mm dia. find the total load, the column can carry, if the stress in steel and concrete is 50MPa and 3MPa respectively.
.ll Asiacell ? 12:33 PM @ 81% HW 4.docx HW4: - The Inverted T section of a L-m simply supported beam has the properties shown in Fig. (4). Find the flange width (b) so that the allowable stresses o ension max =30 Mpa and o compression max.=90 Mpa. 20 mm W KN/m L(m) b(mm) Fig( 4)
Question 17
A reinforced concrete T-beam carries a uniformly distributed super-load on a simply supported span of 8 m. The stresses in the steel and concrete are not to exceed 125 MN/m2 and 7 MN/m2, respectively. The modular ratio is 15, and the density of concrete is 2400 kg/m3. Determine the permissible super-load. (Nottingham) Note the answer in this problem is :144KN (show the solution)
A singly reinforced beam of dimension 200 x 350 is reinforced with 3-25mm at the bottom. If the concrete has a compressive strength of 17MPa and the steel has a yield strength of 415 MPa, determine if the beam can carry a uniform distributed load of 18 kN/m dead load. The beam has a length of 5m with 40mm concrete clear cover, 10mm enclosed stirrups, and Es = 200 GPa. Use LRFD in the analysis.
A floor slab 100 mm thick is cast monolithically with beams 250 mm wide 450 mm deep spaced 1.2 m on centers, on simple supports over a span of 5.0 m. The floor supports a service live load of 2.1 kPa. Using f.-21 MPa, rebar strength f, 415 MPa, calculate the following if a typical interior beam is reinforced with 3- 16-mm-dia. flexure bars at the bottom enclosed with 10-mm-dia. stirrups: 1. Nominal moment capacity (kN-m) of a typical interior beam in positive bending considering T-beam geometry. A. 96.66 C. 91.10 Maximum factored uniformly distributed load (kN/m) a typical interior B. 86.99 D. 81.99 2. beam can sustain against positive bending. В. 27.83 с. 26.23 D. 29.15 A. 30.93 3. Maximum service superimposed dead load in kPa. A. 17.73 C. 16.52 B. 11.08 D. 14.77
Q1) The R.C slab system shown in Figure (1) supported by column line beams and carries a service live load of 5 kN/m and a service superimposed dead load of 3.5 kN/m in addition to its own weight. Slab thickness is 200mm, all beams are (300x600) mm. All columns are 300mm square, use f-25MPA and f=420MP.. According to the ACI-direct design method, determine the following: 6.0m 7.6m 6.0m (a) Design the middle strip bottom bars of the exterior indicated panel shown, in E-W direction. 6.0m 6.0m 7.6m (b)Design the required steel reinforcement at the exterior corner (C). Figure (1)