Example_2: A cantilever beam as shown below has a rectangular cross section of b=200mm, d=390mm, span=2.4m with 3 bars of 22mm diameter, carries a uniform dead load including it s own weight of 12 kN/m and L.L of 10.5 kN/m. Check the adequacy of the section, using fe of 28 MPa and fy of 280 MPa 70 Wd + WL 390 Sol: 2.4 in 200

Example_2: A cantilever beam as shown below has a rectangular cross section of b=200mm, d=390mm, span=2.4m with 3 bars of 22mm diameter, carries a uniform dead load including it s own weight of 12 kN/m and L.L of 10.5 kN/m. Check the adequacy of the section, using fe of 28 MPa and fy of 280 MPa 70 Wd + WL 390 Sol: 2.4 in 200

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

please solve question 4.2, quickly please
USE NSCP 2015
Solve the problem with diagrams and figures in the solution.
CALCULATION: (1) A 6-meter-height column, with pinned boundary conditions at each end, is designed to carry the axial compression valued as 6000kN (the weight of column is included). The section properties of column is given in the following figure. Q235B steel is used. Examine whether the column is satisfactory. 500 Section dimension: 2-500x16 12-450x16 Knowns: The design strength 215N/mm², the yield strength fy=235N/mm². The effective lengths with respect to the two principal axes are identical, 1,= 6m. Class b sections for stability design.
9. A steel portal frame has dimensions, plastic moment capacities and applied loads as shown in the figure. The vertical load is always twice of the horizontal load. The collapse load P required for the development of a beam mechanism is P A B Mp K 2P 2Mp L с Mp D L
A cantilever beam ACB supports two concentrated loads of same magnitude, P as shown in the figure: Calculate the deflection &, at point C. (Use Moment Area method) P P L/2 L/2 B
SHOW COMPLETE FBD
A beam is supported as shown below: В C D E F Hinge Hinge 米 5 m 5 m 6 m 3 m 3 m The beam is to carry the following loads, in (kN) and in (kN/m), in the table below: LOAD w(DL) W(LL) P(LL) SET 1 (1,2,3,4,5) SET 2 (6,7,8,9,0) 20 25 40 30 15 50 Using influence line diagrams, determine the following: 2. Maximum reaction at F, RF in kN.'
A compression member AB (HE 400 B) is pinned at both ends and braced in the weak direction as shown in the figure. Material and geometrical properties are given below. For the given loading and ASD load combination (PG+Pq=3500 KN), determine whether the section is satisfactory or not. Material: 5355 F355 MPa F 510 MPa E= 200000 MPa Section properties (HE 400 B): A: 19780 mm² d: 400 mm h: 298 mm t: 13.5 mm. tr: 24 mm b: 300 mm i,: 170.8 mm İy: 74 mm B X -BRACING IN THE WEAKDIRECTION
Please answer this problem step by step and explain each diragram below and what each one represents
Plz, solve this problem using Flexibility method and show all the steps one by one and draw SFD and BMD Structural Analysis-2
1.)Calculate the height of the neutral axis measured from the extreme compression fiber. 2.) Calculate the strength reduction factor for the given beam. 3.) Calculate the design moment for the given beam. Given b=9.25mm d=152.5mm d(prime)=32.5mm L=1.1m WsubD=6.25kn/m WsubL=8.25kn/m 4 25mm tension steel bars 4 12mm compression steelbars FsubC(prime)=28Mpa FsubY=420Mpa