1. A spiral column is 430 mm in diameter and is reinforced with 7- 28 mm bars Grade 415. The spirals are 10 mm in diameter and concrete cover used is 40 mm. If f'c = 28 MPa, and the column has an unsupported length of 2.20 m, what is the safe ultimate load that the column can support using the 2015 NSCP specifications? Neglect moment in the column. Ku = 1.0

1. A spiral column is 430 mm in diameter and is reinforced with 7- 28 mm bars Grade 415. The spirals are 10 mm in diameter and concrete cover used is 40 mm. If f'c = 28 MPa, and the column has an unsupported length of 2.20 m, what is the safe ultimate load that the column can support using the 2015 NSCP specifications? Neglect moment in the column. Ku = 1.0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate Mn
3) Calculations Steel Structure Corridor Dead Load = (uniform load) Live Load = 80 psf (uniform load) Find Ac 15
A TIMBER BLOCK "B x B" mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A "B" mm AND 't' mm THICK STEEL PLATES. DETERMINE THE THICKNESS 't' SO THAT THE ASSEMBLY WILL SUPPORT AN AXIAL LOAD OF 1000 KN WITHOUT EXCEEDING A MAXIMUM TIMBER STRESS OF 12 MPa OR A MAXIMUM STRESS IN STEEL OF 350 MPa. MODULUS OF ELASTICITY OF STEEL AND TIMBER ARE 210 GPa & 7 GPa RESPECTIVELY. B t B t PROB 04
A bracket with bw = 350 mm and h = 450 %3D mm protruding from a beam column is subjected to a reaction force RD = 140 kN by a fixed load in a vertical direction at a = 180 mm position and a reaction force RL = 160 kN by a loading load. Additionally, fck = 28 MPa and fyt = 400 MPa are placed integrally with normal weight concrete. Design the bracket using these conditions.
Problem: Using WSD & USD, design the midspan reinforcement of stringer (B-3) for the second floor of a 3-storey residential building shown below. Use 20.7MPa compressive strength of concrete @ 28-days and grade 40 reinforcing bars. Use Ye= 24.5 KN/m³. Design the stringer as rectangular beam. Assume simply supported. 450mm 250mm 250mm 450mm, Superimposed Deadloads = 2.70 KPa Stirrups = 10mmo Main bar = 25mm 350mm B-4 STAIRWELL B-1 250x400mm S-3 B-3 250x400mm S-4 (3000) mm 350mm B-4 350mml Stringer Section (2000) mm (3500) mm (2000) mm 700mm
1/ Calculate maximum deflection of the beams (This was solve it) 2/ Check the suitability of the section assuming the code limitation of L/240. 3/ If maximum deflection doesn’t meet the code requirement, propose your solution
using the table below, answer the question
A 300mm x 425 rectangular beam is reinforced for tension only with 4-28mm bars. The beam has a concrete cover of 40mm and a stirrup of 10mm diameter bar. The beam carries a live load and a dead load (without its self-weight). Given that unit weight of concrete is 24kN/ cu.m f'c = 21 MPa and fy = 414 MPa, calculate the additional concentrated live load as shown in the figure.
H.W.5: For the simply supported beam shown below reinforced by 4025 bars (fy= 420 MPa), the concrete strength (f= 21 MPa) evaluate the following: 1- Check the actual flexural stresses in concrete and steel if the span length equal to (4 m), dead load 8 kN/m including self-weight of the beam, live load equal to 10 kN/m. 2- The length of beam span that makes the concrete in tension face starts to crack. 3- The actual stress in concrete and steel if the span length of the beam is equal to 7 m. WI= 10 kN/m Wd=8 kN/m 420 mm 500 mm 마 350 mm
Given a concrete column that would be required to support loads of Pu=400kips and Mu=50 kip-feet, we will determine the column interaction curve and decide if the column is adequate for this particular application. The column will be a 14”x14” square, tied column with #9 bars at the corners. The center of the reinforcement in each corner is 3” from each of the sides. The f’c of the concrete is 4 ksi and the reinforcement is Grade 60. Determine if the column is acceptable for this application. Calculate the value of Mu and Pu.