A tied column of dimensions 300x450mm is reinforced with 6 bars of 28mm diameter. Also, ties of 10mm diameter are used at a spacing of 300mm. The compressive strength of concrete is given as 28MPa and the yield strength of steel is given as 420MPa. Determine the maximum ultimate load on the column.

Q: Concrete Reinforcement Width of section Reinforcement strengths. fcu:= 30-MPa fy:= 450-MPa b:= 280…

A:

Q: Design the steel reinforcement for flexural for the beam shown in the fig. below. given f'c-28 Mpa,…

A:

Q: he slab has beam between all supports which are poured monolithically with the slab as shown in the…

A: slab thickness = 150mm support width = 350mm Effective length along x axis lx = clear span + depth…

Q: The properties of the reinforced concrete beam are b = 316 mm, d = 479 mm, Ast = 1275 mm2, and Est /…

A: NOTE : the given data is Indian standard data

Q: 1. In pre-stressed concrete application, the pre-stressing force is reduced with time because of: a.…

A: Solution: 1. In pre-stressed concrete application, the pre-stressing force is reduced with time…

Q: 2. From the figure shown, fc' = 20 MPa, fs = 140 MPa, and n = 12. Determine the moment capacity of…

A: Answer  To calculate the Moment capacity of concrete and steel we have equation of stress in…

Q: (3) for Normal weight Concrete, using ACI Code and recommendation for high strength concrete, to…

A: Solving first questionGiven datacompressive strength of concrete given in table findmodulus of…

Q: n exterior beam has 300 mm and a height of 600 mm, it is reinforced with 5-p25 mm bars for tension…

A: Given : an exterior beam has 300 mm and a height of 600 mm, it is reinforced with 5-p25 mm bars for…

Q: For normal-weight concrete. fé (psi) 3000 4000 5000 6000 7000 8000 9000 Ec (ksc) Let M= fr (psi) n…

A: Answer As per ACI code 318-19 clause 19.2.2, Elastic Modulus for normal weight concrete is given by…

Q: 3m 200 ↓ 8m GkN/m B 十 -2m-

A:

Q: A UNIFORMLY DISTRIBUTED FORCE OF Px=3 (COMPRESSION), Py=6 (TENSION) AND Pz=9 (COMPRESSION) IN THE X,…

A: Given data  Px=3KN (COMPRESSION), Py=6KN (TENSION) AND Pz=9KN (COMPRESSION) IN THE X, Y AND Z…

Q: CA Calculate the Compressive svength fom %3D Jエ 28 9 af =64000 Also write the conclusion and unit.

A:

Q: Determine the design strength of the beam. Use F'c= 28 MPa, Fy = 415 MPa, b = 250 mm, d' = 60 mm, d…

A:

Q: In the extreme fiber of a concrete beam, the value of compression is 5.80 MPa. The neutral axis of…

A: Given: Compressive stress = 5.80 MPa Depth of neutral axis, y = 58 mm Compressive strength of…

Q: An HSS9 x 7 x3⁄8 filled with concrete is used as a composite column, as shown in Figure. The steel…

A: Pu=1.2PD+1.6PL Here PD=65 Ksi PL=130 Ksi Pu=1.2(65)+1.6(130)=286 Kips

Q: 2. In the beam flexural test of concrete shown, calculate the flexural strength, 100 mm 100 mm…

A:

Q: Q2 : Design the simply supported reinforced concrete beam showing in the Figure below for bending…

A: Given : fc =20 MPa, fy = 300 MPa Ultimate strength design method 22 mm dia main reinforcement and…

Q: A 3 m concrete column 300 mm in diameter is reinforced with 5 - 15M steel rods (reinforcing bars).…

A: Given: Diameter of the column   D=300 mmarea of column  A=π4×D2=π4×3002=70685.83 mm2Area of the…

Q: The flexural tensile strength of M25 grade of concrete, in N/mm², as per IS:456-2000 is A 0.5 B 5 C…

A: Given- M25 concrete grade of concrete, IS 456:2000,

Q: Assuming concrete is un-cracked. Determine the cracking moment of the section. E, = 2*10°MPA E =…

A: Given data  Width Elastic modulus  Stress in concrete  Number of bars Diameter  Height

Q: r is designed to ca 20KN. Using allow 20MPa and ỢC = 6

A:

Q: g. Distance of the compression concrete force from the neutral axis (mm)

A: Given data: Concrete strength, f'c=28 MPa Maximum moment =320 kNm  Effective cover of beam=90 mm…

Q: For the inverted precast concrete T- beam Steel reinforcement consists of four bars each with a…

A:

Q: A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z…

A:

Q: Areinforced concrete column contains longitudinal steel equal to 1 percent of net cross-sectional…

A: This question is related to the Design of RCC Structure.

Q: A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars.…

A:

Q: ASAP DONT REJECT ME, I'LL GIVE UPVOTE THANK YOUU Solve the basic development lengths in tension for…

A:

Q: From the beam shown, fc' = 28 MPa, fy = 414 MPa, Bh = 1.20, Cc = 40 mm. Take D = 28 mm diameter…

A:

Q: 6m-simply supported beam cross-section is show in the figure below is prestressed with 15 wires of…

A:

Q: Assume straight line instead of parabola for stress-strain curve of concrete as given below and…

A:

Q: From the figure shown, fc’ = 18 MPa, fs = 128 MPa, and n = 10. Determine the moment…

A:

Q: c) Find the stresses in the concrete and the reinforcement for the following applied moments: (i) -…

A: Modular ratio has to be determined.Lever arm has to be determined.Then the stress in concrete and…

Q: c) Find the stresses in the concrete and the reinforcement for the following applied moments: (i) -…

A: Given:b=300 mmh=520 mmEc=30 GPaEs=200 GPad=460 mmAs=1470 mm2 Modular ratio has to be determined.…

Q: Concrete Design 48" 6 #9 18 fy = 60 ksi fc = 4 ksi h₂=6 Calculate strain in tensile steel Is the…

A: bw  = 18 ind = 26 inhf = 6 inb = 48 in6 #9 rebarscover = 3 infc = 4 ksify = 60 ksi

Q: A RECTANGULAR ALUMINUM BLOCK IS 110mm LONG IN THE X DIRECTION, 70mm WIDE IN THE Y DIRECTION AND 85mm…

A:

Q: a-Design the concrete column to carry the applied load Concrete allowable strength: 35 MPa P= 900 kN…

A: Given:- The concrete allowable strength = 35 MPa The magnitude of the load = 900 kN The column…

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.