Directions: Check the safety of the typical reinforced concrete tee beam used to support the concrete roof of the community center building. The beam cross section and the reinforcement is as shown here and the loading schedule for the floor area is provided below. Fy = 60 ksi F*c=3,000 psi SECTION ●● be 6=8 Bars ¤T -3'-6"- DEAD LOADS 1. Self Weight of the Beam 2. Slab Weight LIVE LOADS 1. Snow Loads: 60 lb/ft²

Directions: Check the safety of the typical reinforced concrete tee beam used to support the concrete roof of the community center building. The beam cross section and the reinforcement is as shown here and the loading schedule for the floor area is provided below. Fy = 60 ksi F*c=3,000 psi SECTION ●● be 6=8 Bars ¤T -3'-6"- DEAD LOADS 1. Self Weight of the Beam 2. Slab Weight LIVE LOADS 1. Snow Loads: 60 lb/ft²

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

: ۷:۲۹ ۱ 1- Flat slab without edge beam and without drop panel 2- Use edge beam only. 3- Use Drop Panel only. 4- Use edge beam and drop panel. 5- Use beams for all lines with am = 0.5. For the slab shown in the figure, Fy= 420 Mpa, Col. Dimensions = 400 x 400 mm, check slab thickness at exterior panel for deflection control for the following cases: 6- Use beams for all lines with am = 1.5. 7- Use beams for all lines with am= 2.5. Discuss the results. 2_53528712391174... AMX36 36. 7.2 m 7.2 m ****************………………….. 7.2m 7.2 m 7.2 m 7.2 m
Please show intermediate steps including free diagrams, equations used, and problem setup, so that your approach can be followed
Create a flowchart for Doubly Reinforced Beam Design and Analysis
Once the beam has been selected, why is the shear formula used?
write and describe the steps and stages of designing a rail of the raiway track
Answer number 3 pls
But how would I plot the stresses as a function of L/h ?
3. Please show your complete solution
List the materials from which level rods are made up of.
What is an optimal duct system for a two-storey house without any partitions in both floors (the 1st and 2nd floor is a large open area without any boundaries except for the bathroom in the 1st floor)?
ASAP
Given the tabulation below, compute for the following: 1. Storey Shears, Vx 2. Storey Forces, Fx 3. Compute the Overturning Moment 4. Compute the Resisting Moment 5. Compute the Factor of Safety 6. Is the building safe against overtuning, Explain? Tabulation: Level Wx hx Wxhx Fx Vx Floor Ht. Fxhx(KN.M) RD 1950 3.5 7 1800 3.5 1800 3.5 5 1700 3.5 4 1650 3.5 3 1550 3.5 2 1500 3.5 1. 1400 6. Design Parameters: 1. Assuming the total base shear V is 1800 KN and T=0.64 secs. Since the value of T<0.70 secs, the value of F; is equal to zero. The remaining lateral forces can be distributed using the following formula; 2. Considering the height-width ratio to 0 .50 or less, if the total height of the structure h=24m, let us assume the width of the building shall be 14m in both direction.