A conical clutch has an inclined angle of 120. The outer and inner diameters are 80 mm and 20 mm respectively. Calculate the force required to press the two halves together if it is to transmit 200 W at 600 rev/min. The coefficient of friction is 0.3. Use both the uniform wear theory and the uniform pressure theory.

A conical clutch has an inclined angle of 120. The outer and inner diameters are 80 mm and 20 mm respectively. Calculate the force required to press the two halves together if it is to transmit 200 W at 600 rev/min. The coefficient of friction is 0.3. Use both the uniform wear theory and the uniform pressure theory.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A cone clutch is mounted on a shaft which transmits power at 200 rpm. The small diameter of the cone…

Q: Q5: The block brake, as shown, provides a braking torque of 360 Nm The diameter of the brake drum is…

Q: multi-disc clutch has three discs on the driving shaft and two on the driven shaft. The inner…

A: Given data: The number of driven plate is n1=2 The number of driving plate is n2=3 The inner…

Q: A cone clutch with a cone angle of 12° transmits 53 kW at 1300 rpm. The coefficient of friction of…

Q: shows two pulleys are fixed to the shaft and supported by the roller bearing at points A and B.…

A: Given Data:

Q: A cone clutch has an angle of 12 dgrees and coefficient of friction of 0.42. Find the axial force…

Q: A multi-disk clutch consists of two steel disks with one bronze disk. The inner and outer diameters…

A: Given data:

Q: The tension in a pulley belt is 300 N when stationary. The smaller pulley has a diameter of 300 mm…

Q: A conical clutch has an included angle of 150. The outer and inner diameters are 100 and 40 mm…

A: Given data:Since, the clutch is of two halves.So, the cone angle of the clutch isOuter diameter,…

Q: 30° Q9/ braking system has its braking lever inclined at an angle of 30° to the horizontal plane, as…

Q: A multi-plate clutch has four pairs of frictional surfaces, each of internal diameter 120 mm and…

A: Clutch is defined as a machine element which is used to engage and disengage driver and driven shaft…

Q: solve show solution

Q: A multi plate clutch has three plates and four pressure plates, pressed together by an axial force…

A: Given Total plates = 7 Total contacting surfaces, n = 7-1 =6 r2 = 100mm r1 = 80 mm W = 500N

Q: Two parallel shafts whose centre lines are 4 m apart, are connected by an open belt drive. The…

A: In this problem, a diameter of larger pulley is taken as D2=3 m and a diameter of smaller pulley is…

Q: A centrifugal clutch is to transmit 15 kW at 900 r.p.m. The shoes are four in number. The speed at…

A: Centrifugal clutches generally consists of motor pulleys. Inside the rim of these pulleys, various…

Q: A double thread ACME screw driven by a motor at 534 rpm raises the attached load of 1,062 kg at a…

Q: 4.) A flat belt makes contact with an 18 in. diameter pulley through half its circumference. If the…

Q: A multiple V-belt drive is required to transmit 4 kW. The smaller pulley of the system is 150 mm…

Q: l-plate clutch must transmit 23 kW of power without slipping at 2500 rev/min. The coefficient of…

Q: A single disc clutch is used to transmit 12kW power at 1000rpm. The axial pressure is limited to…

Q: A conical clutch has an included angle of 105°. The outer and inner diameters are 110 mm and 40 mm,…

A: Consider 'W' be the axial load on the clutch, R and r be the outer and inner radii of the clutch…

Q: The figure shows an internal rim-type brake having an inside rim diameter of 300 mm and a dimension…

Concept explainers

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.

Question

A conical clutch has an inclined angle of 120.
The outer and inner diameters are 80 mm and
20 mm respectively. Calculate the force required
to press the two halves together if it is to transmit
200 W at 600 rev/min. The coefficient of friction
is 0.3. Use both the uniform wear theory and
the uniform pressure theory.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Clutches, Brakes, Couplings and Flywheels

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A turnbuckle is used to connect two rods, one having right handed and other, having left handed V-threads. The angle of V-threads is 60 degrees. The rods have a mean diameter of 2 cm and 3 threads per cm. The coefficient of friction between the rods and the nut connecting the rods is 0.15. Find the forque required on the nut to produce a pull of 4 kN. Assume that rods do not twist.
The clutch of a motor car is required to transmit 9 kW at 3500 rpm. It is of single-plate type, with both sides of the plate being effective. The coefficient of friction is 0.25 and the maximum pressure is limited to 82 N/cm2. The ratio of diameters is 1.4. Assuming uniform wear determine: (You should upload the answers in the Link provided for submitting the assignment, typing the answers in the box provided below is optional). The internal diameter of the plate in mm The external diameter of the plate in mm
i need the answer quickly
Q6 Engine developing power at 1000rpm is fitted with a cone clutch having the face width of the clutch equal to 106mm. The cone has a face angle of 12°and the engagement factor is 1.5. If the mean normal pressure on the clutch face is not exceeding 0.07MPa and the coefficient of friction is 0.2, the axial spring force necessary to engage the clutch is 1796N. Requirements: 1) The mean diameter of the cone clutch. 2) The developing power. 3) Complete the construction drawing by showing all the details. Engine Engine Shaft Or Driven Shaft Female Cone Sleaves 8080 ਬੇਬਰਹੁਡ Splines Spring Friction Lining Pedal Gearbox Shaft Driven Shaft Gearbox
A flat belt is required to transmit 35 kw from a pulley of 1.5 m effective diameter running at 300 rpm. The angle of contact spread over 11/24 of the circumference and the coefficient of friction between pulley and belt 0.3. Determine width of belt required. It is given that the belt thickness is 10mm, density of its material is 1.1Mg/m and the related permissible working stress is 2.5 Mpa.
In an engine governor of the Porter type, the upper and lower arms are 200 mm and 250 mm respectively and pivoted on the axis of rotation. The mass of the central load is 15 kg, the mass of each ball is 2 kg and friction of the sleeve together with the resistance of the operating gear is equal to a load of 24 N at the sleeve. If the limiting inclinations of the upper arms to the vertical are 30° and 40°, find, taking friction into account, range of speed of the governor.
A cone clutch has D = 16 in, d = 14 in, a cone length of 3 in, and a coefficient of friction of 0.35. A torque of 3 kip-in is to be transmitted. For this requirement, estimate the actuating force and pressure by both models.
A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt andpulley is 0.3, semi V-groove angle is 22.5o and angle of contact of belt with the pulley is 160o. Ifthe mass of the belt is 0.45 kg/m and if permissible pull in the belt is 800 N. Calculate the power.Consider the centrifugal tension in the belt.
A cone clutch is to transmit 7.5 kW at 900 rpm. The cone has a face angle of 12o. The width of the face ishalf of the mean radius and the normal pressure between the contact faces is not exceeding0.09Nmm2⁄. Assuming uniform wear and the coefficient friction between contact faces as 0.2. Find themain dimensions of the clutch and the axial force required to engage the clutch.
will down vote if wrong
A multiple disc clutch has radial width of the friction material as 1/5th of the maximum radius. The coefficient of friction is 0.25. Find the total number of discs required to transmit 60 kW at 3000 r.p.m. The maximum diameter of the clutch is 250 mm and the axial force is limited to 600 N. Also find the mean unit pressure on each contact surface.
A multi-plate clutch must transmit 11 kW of power without slipping at 1500 rev/min. The coefficient of friction is 0.3. The inner and outer radis are 30 and 85 mm respectively. The axial force applied to the plates is 780 N. Determine the number of plates required using.