Consider a pulley and a flat belt. Static and kinetic friction coefficients between the pulley and belt are 0.2 and 0.25 respectively. Find T2 if T1 = 100 N. Assume clockwise rotation of the pulley. %3D 150 T2 T1

Q: ng based on the degress scal from 0 to 72

A: 4 steps are present in the IC cycle. inlet compression power exhaust

Q: Which of the following statements is not true? Select one: O a. Reports can contain bulleted or…

A: As we know Equations should be written in a symmetric manner, not just in the left margin. Equation…

Q: Q/Draw S and B-M D 8 kuim

A:

Q: A Contractor/foreman needs lumber to be used for wooden scaffoldings, the set of lumber can be…

A:

Q: The horizontal V fitting, steady, uniform flow at each section, incompressible, and neglect weight…

A:

Q: Hi, -26.088 or 333.911 is INCORRECT for Ox please recheck

A:

Q: But there is no 2 & 4 option to the multiple choice

A: Explanation: The interior of the semi circular log is made hollow so definitely center of gravity…

Q: dy 35+メ9

A: The provided differential equation is given as, dydx=3y2+xyx2

Q: If 17 welders can complete a job in 134 hours, how long will it take for 21 welders to do the same…

A:

Q: The power of the prime mover running a pump is 20 HP, and the power out of the pump is 19 HP, what…

A:

Q: Iron Ore are mainly used to produce high heat in blast furnace Select one: True False CamScanner

A: Iron ore are mainly used to produce high heat in blast furnace.

Q: A part may be properly represented on an engineering drawing with as few views as: A. one B. two…

A: Please find the answer in the next page.

Q: Finding the y centriod.

A: Given data, the I section is given with dimensionFind outthe centroid along the y-axis

Q: 5 kips 3'-0" 3 kips 3'-0" 8 kips + 5'-0" The net force acts on this system is 12 kips 2'-0" 2 kips

A: Given:A simply supporetd beam with the following forces acting on it:5 kips, 3 kips, 8 kips, 12…

Q: Oil relation between the shear stress and rate of deformation is given in the figure, If the oil…

A: The relation between shear stress and rate of deformation is - τ=μdudyμ=τdudyThe slope of the graph…

Q: Question 20 Not yet answered Marked out of 2 Choose. question Stainer Match the following questions…

A: wiper seal is an axial seal that makes a seal whereas permitting a reciprocating shaft to pass…

Q: Relative angles provide more information about segment position than absolute angles Select one:…

A: Given Data : Relative angles Absolute angles

Q: where did you get 0.157

A: Given:Figure with dimension is providedTo find:Percent reductions in areaPercent reduction in area…

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: O I'd love ice-cream I love ice-cream

A: Correct is I love ice-cream.

Q: means the repair work done to keep the system in good working condition.

A: we will discuss an activity/ process that is involved with work  done to keep the system in good…

Q: The tank contains water and immiscible bil with S=0.70. What is h in cm? h 6 cm 12 cm Oil Water

A:

Q: Iron Ore are mainly used to produce high heat in blast furnace

A: I think its answer should be False. Because blast furnace is used to melt iron ore by reducing…

Q: Only one of the following is correct. Select the correct answer. Continuous process production has…

A: Given: Multiple choice question

Q: Q.1) Knowing that the tension in cable BA is 570 N, determine the moment about O. Neglect the…

A:

Q: What's the answer C onwards with working and correct answer and can you label it please as I have…

A: The ideal diesel cycle does not occur in practical life because the losses are not eliminated in…

Q: can tutor continue the next two questions also

A:

Q: Stoker

A:

Q: idk where you got the 4 from

A: The number of independent equations=5The number of unknowns=7To determine:Degree of freedom

Q: can tutor explain the what is all of the equations means and also answer the next 2 questions

A: To solve the physics problems, let's break them down one by one:1) Calculate the force experienced…

Q: How many cutting-plane lines are shown on this print?

A: Cutting plane lines:Cutting plane lines are the lines used to show the direction of the cut-way…

Q: Read the following statement and choose the most appropriate answers. Statement 1 For a measuring…

A: Accuracy is defined as how close is the measured value to the true value.

Q: how did you get 0.7967

A: The power output of the turbine is 0.80208 H.P.

Q: A 15-meter long beam-tank assembly supports the loading shown in addition to its weight, which is a…

A: The outer diameter of cylinder is .The inner diameter of cylinder is .

Q: What does the shear flow measure?

A: The shear flow is defined as the shear force per unit length in a thin walled perimeter. The…

Q: False

A: It is False. Higher the gauge number, indicates thinner the sheet metal.

Q: 13- Drawing sheet table contains class item. O True O False 12- The drawing sheet can be used both…

A: 13. in drwaing sheet tables are used to specify each part and its materials to do machining  so the…

Q: Which of the following statements are correct? Select all that apply.

A: A hurricane is a monster of a storm! Strong winds spiral inward and upward at speeds of 75 to 200…

Q: The feature of saw blade geometry that allows the blade to cut a kerf that is wider than the blade…

A: A feature is responsible when a blade cut a kerf which is wider than the blade itself.

Q: 0le A. An outside caliper can be used to measure the diameter of a

A: Caliper is used to measure the linear dimension, diameter of a hole and outer diameter of a shaft.…

Q: The water (density =1000 kg/m3) leaves the nozzle (area of the nozzle=0.01 m). Assuming steady,…

A: GIVEN :- height of stagnation tube : h= 50 cm area of nozzle : A= 0.01 m2 S.G = 10.4  ρ=10400 kg/m3…

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.