what is the xbar distance (from left edge of part)?

Q: The temperature distrībution in a certain plane wall is T--Ci+C°+C3ư T- T1 where 7i and T, are the…

A:

Q: A cylindrical tank is resting horizontally on the ground (the circular faces are vertical). The tank…

A: There are two types of forces that act on a circular surface: one type of force is radial force and…

Q: Make the part program using CNC code.        Tool Dia. = 6 mm        depth of cut 3.0 mm…

A: Tool Dia. = D =6 mm depth of cut = d= 3 mm (Use G90 code)  To find: Make the part program using CNC…

Q: how o create all parts list after the drawing ?

A: Given question: how to create all parts list after the drawing ?

Q: An uncontrolled 1050 kg car strikes squarely a motorway crash cushion in which the car is brought to…

A:

Q: What is the sketch of the right face

A:

Q: 2 02 5 A 6 7 08 8 3 B с 9 4 D E

A: The J1 refers to the binary joints or the lower pairs in the given mechanism while J2 refers to the…

Q: Please answer attach file

A:

Q: create 2 fourbar designs that include the dimensions and angle of motion

A: It is asked to draw four bar mechanism with given motion

Q: A sprinkler system pumps water through a large pipe inlet with a diameter (d1). The pipe then breaks…

A: (c) To check: Whether the flow is laminar or turbulent. Given: The diameter of pipe 1 is d1=10 mm.…

Q: Another name for "SIZE DESCRIPTION is: 37 A Dimensioning B Orthographic projection. C Assembly…

A: Given Engineering drawing To find Size description Leader line Extension line

Q: Consider the steady, incompressible, viscous and fully-developed flow through a horizontal circular…

A:

Q: 3. FBD for AK to determine the internal forces on K: forces/reactions on the AK; a. There are b. Sum…

A: In this problem, it is asking for question (3) so we will provide the solution for question (3)…

Q: Determine the magnitude of the internal loads(normal, shear, and bending moment) at point C.

A: The given member can be cut into two parts along C and the above part can be drawn as below, Here,…

Q: Define a point. Also describe projection planes like horizontal plane (H.P), & vertical plane (V.P).

A:

Q: (a) Draw neat illustrative sketches to bring about the difference between a helical coil tension…

A: Helical spring -These types of springs are made of wire. These springs are supposed to carry load in…

Q: A fluid of density 840 kg/m and dynamic viscosity 1x103 Pa.s flows through a pipe of diameter 21 mm…

A: given datadensity of fluid (ρ) = 840 kg/m3dynamic viscosity = 1×10-3 Pa.sdiameter of pipe = D = 21…

Q: Ball B (10 kg) is on a rod on which a torque of M = (2t² + 4) Nm where t is in seconds. Fin the…

A:

Q: The sheet metal form as shown in Figure Q5 and has a dimension with x, y and z axis respectively.…

A:

Q: Question6 In the following system the coefficient of friction between all contact surfaces is .…

A:

Q: mechanism shown, and state the character of the assembly. The number of Links L is

A: Identify the number of links, full joints and half joints, and then determine the degree of freedom…

Q: 1. 100 mm The bar has a diameter of 60 mm. If it is subjected to the force components as shown in…

A:

Q: ANSWER COMPLETELY FOR UPVOTE a. When do we say that the body is accelerating? b. What's the…

A: (a). When velocity of a body increases with respect to time, we say that the body is accelerating.…

Q: ASME Y14.5-2009. PART TO BE FREE OF BURRS AND SHARP EDGES. D.001 VACUUM, BAKE (10-4 TO 105 TORR).…

A: If will attached part by part look like heat tube exchanger

Q: Find the heat transfer per unit area through the composite wall in Figure P2-4. Assume…

A:

Q:

A: There are three views that can be drawn by using an isometric drawing. TOP View SIDE View FRONT…

Q: We begin with Direction A. (a) What is the x coordinate of the vector tail (x₁)? (b) What is the x…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: What is the geometric term that applies to V-groove

A: V - Groove      The general geometry of v groove is two lines for example AB and BC, joined together…

Q: Draw a complete FBD clearly labeled.

A:

Q: haft G-Codes programming process (sumerik)

A: CNC programmers increasingly face special tasks that take them to the limits of classic (DIN 66025)…

Q: In order to produce the L-Holder shown you must read the dimensions on an Engineering Drawing.…

A: Given:- Engineering drawing of L-holder with dimensions Top view, Front view, Side view, and…

Q: Determine the maximum shear force V that the strut can support if the allowable shear stress for the…

A: Here we will use the formula for symmetric I section

Q: Two farmers are pushing on a gate with forces FA and FB, applied at locations A and B respectively.…

A: Given : To find : moment at C

Q: Please answer attach file

A: Given dataStress in x direction σx = -27MPaStress in y direction σy = 5.5MPaShear stress ζ =…

Q: At what temperature does water boil if P = 0.04 bar O a. 35.6 C O b. 81.6 C Oc. 85.94 C O d. 42.5 C…

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.