Q6 Engine developing power at 1000rpm is fitted with a cone clutch having the face width of the clutch equal to 106mm. The cone has a face angle of 12°and the engagement factor is 1.5. If the mean normal pressure on the clutch face is not exceeding 0.07MPa and the coefficient of friction is 0.2, the axial spring force necessary to engage the clutch is 1796N. Requirements: 1) The mean diameter of the cone clutch. 2) The developing power. 3) Complete the construction drawing by showing all the details.

Q6 Engine developing power at 1000rpm is fitted with a cone clutch having the face width of the clutch equal to 106mm. The cone has a face angle of 12°and the engagement factor is 1.5. If the mean normal pressure on the clutch face is not exceeding 0.07MPa and the coefficient of friction is 0.2, the axial spring force necessary to engage the clutch is 1796N. Requirements: 1) The mean diameter of the cone clutch. 2) The developing power. 3) Complete the construction drawing by showing all the details.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A slurry pump is to be driven by a 50 HP, 2400 rpm diesel engine and operating under moderate shock…

Q: A multiple-disk clutch is to operate in oil and be able to transmit a design overload torque of 800…

A: Given:T = 800 N-mDo = 150 mm = 0.150mDi = 90 mm = 0.09mpmax =1000 kPaf = 0.10To findTotal number of…

Q: A hydraulically operated multidisk plate clutch has an effective disk outer diameter of 6.0 in and…

Q: A conical clutch has an included angle of 150. The outer and inner diameters are 100 and 40 mm…

A: Given data:Since, the clutch is of two halves.So, the cone angle of the clutch isOuter diameter,…

Q: A vertical Venturi meter, 150 mm in diameter is connected to a 300-mm diameterpipe. The vertical…

Q: The axial load, mean radius, coefficient of friction, number of friction pairs are used to find the…

Q: иво Pulley B 2 m 150 Pulley A Fig. 5 a) A polyamide F-2 flat belt drive is to be designed with Hd =…

A: Step 1: Step 2: Step 3: Step 4:

Q: l-plate clutch must transmit 23 kW of power without slipping at 2500 rev/min. The coefficient of…

Q: Q2) A flat belt drive system is to be) designed for an application in which the input shaft speed is…

Q: QUESTION 3 In an axial clutch, the clutch plate has an outer diameter of 15.0 inches and an inner…

Q: In an axial clutch, the clutch plate has an outer diameter of 15.0 inches and an inner diameter of…

A: Given data Outside diameter of clutch plate, do=15 inInside diameter of clutch plate, di=5…

Concept explainers

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.

Question

Q6 Engine developing power at 1000rpm is fitted with a cone clutch having the face
width of the clutch equal to 106mm. The cone has a face angle of 12°and the
engagement factor is 1.5. If the mean normal pressure on the clutch face is not
exceeding 0.07MPa and the coefficient of friction is 0.2, the axial spring force
necessary to engage the clutch is 1796N.
Requirements:
1) The mean diameter of the cone clutch.
2) The developing power.
3) Complete the construction drawing by showing all the details.
Engine
Engine Shaft
Or
Driven Shaft
Female Cone
Sleaves
8080
ਬੇਬਰਹੁਡ
Splines
Spring
Friction Lining
Pedal
Gearbox Shaft
Driven Shaft
Gearbox

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: calculate mean diameter

VIEW

Step 3: calculate power

VIEW

Step 4: drawing of cone clutch

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 22 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A cone clutch has D = 16 in, d = 14 in, a cone length of 3 in, and a coefficient of friction of 0.35. A torque of 3 kip-in is to be transmitted. For this requirement, estimate the actuating force and pressure by both models.
A)It is required to use a multiplate clutch to transmit power of 24 kW at 1200 r.p.m. If the clutch has the following data: • The Outer and inner plate radii are 120 mm and 80 mm respectively. • Maximum axial pressure pmax=0.12 N/mm?. • Coefficient of friction=0.3. Find: 1. The axial load (W) required. 2. The number of effective pairs of contact surfaces (n).
A multiple clutch has to transmit 90kW from an engine running at 3500 rpm. Clutch lining outer diameter is 200mm and inside diameter is 160mm. Spring pressure on clutch is 170kPa and it's coefficient of friction is 0.28. a)Calculate the minimum clamping force required b) Calculate the no. of clutch plates.
Q: A multi disc clutch is used to transmit to 10 kW power at 900 rpm. If the external diameter of friction lining is 1.25 times the internal diameter, find the required dimensions of the friction lining and the axial force exerted by the oil chamber pressurized to engaged the disks a with disks b. The pressure between disks is limited to 0.085 N/mm?. Assume average service condition. The coefficient of friction may be taken as 0.3. Disks a Disks b Seals Oil chamber (pressurized to engage clutch) Piston Bushing Oil passage Output Key Key Input Oil passage Page 1 of 1
A cone clutch with a cone semi-angle of 120 is to transmit 11.19KW at 750rpm. The width of the face is 1/4th of the mean diameter and the normal pressure between the contact faces is not to exceed 8.27 X 104 Pa allowing the co efficient of friction of 0.2, Determine the main dimensions of the clutch and the axial force required.
Solve show solution
Q3-a/ What are the characteristics of material which used for lining friction surfaces of a clutch? (5Marks) b/ An engine developing 45 kW at 1000 r.p.m. is fitted with a cone clutch built inside the flywheel. The cone has a face angle of 12.5° and a maximum mean diameter of 500 mm. The coefficient of friction is 0.2. The normal pressure on the clutch face is not to exceed (0.1 N/mm2). Determine: 1. The face width required, and 2. The axial spring force necessary to engage the clutch Answer question 4 or 5 (15 Marks) 15 Q4/ The areas of the turning moment diagram for one revolution of a multi-cylinder engine with reference to the mean turning moment, below and above the line, are - 32, + 408,-267, +333,-310, +226,- 374, + 260 and 244 mm². The scale for abscissa and ordinate are: 1 mm = 2.4° and 1 mm = 650 N-m respectively. The mean speed is 300 r.p.m. with a percentage speed fluctuation of± 1.5%. If the hoop stress in the material of the rim is not to exceed 5.6 MPa, determine the…
A clutch functions to continue the power of 110 Hp and 3600 rpm rotation, number of clutch plate 1, The total force of the spring suppressor 1500 N, correction factor 0.95 and friction coefficient 0.3 Calculate the Measures of Do and Di if the ratio of Do: Di = 3: 2