A multiple-disk clutch is to operate in oil and be able to transmit a design overload torque of 800 N. m. The disks are alternately high-carbon steel and molded asbestos, with inside and outside diameters of 90 and 150 mm, respectively. Design values based on test experience for this application are Pmax = 1000 kPa and f = 0.10. What total number of disks is required? Also, what minimum clamping force is required to transfer this torque through the clutch? == Ans. (8 Molded Asbestos Friction Disks and 9 High-Carbon Steel Plates) Note: The number of friction interface surfaces: N = 16. FClamping = 8333 N

A multiple-disk clutch is to operate in oil and be able to transmit a design overload torque of 800 N. m. The disks are alternately high-carbon steel and molded asbestos, with inside and outside diameters of 90 and 150 mm, respectively. Design values based on test experience for this application are Pmax = 1000 kPa and f = 0.10. What total number of disks is required? Also, what minimum clamping force is required to transfer this torque through the clutch? == Ans. (8 Molded Asbestos Friction Disks and 9 High-Carbon Steel Plates) Note: The number of friction interface surfaces: N = 16. FClamping = 8333 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 200 1s' the Reaction A the Reactions L L Oetermine the value 2. Determine the value 9, the value The…

Q: Required information NOTE: This is a multi-part question. Once an answer is submittec Consider the…

A: P = 815 N

Q: 16. The forces 8,4/3 ,6v3 and a point, the measure of the ang first force and the second force the…

A: Given F1=8NF2=43N=6.92 NF3=63N=10.39NF4=14N To find Magnitude of Resultant

Q: The figure below shows the components of normal forces, the value of radial force on the gear wheel…

A: Write the given value using suitable variables. Here Ft signifies tangential force, and 0 signifies…

Q: 6) Young's modulus and density of glass fiber are 85 GPa and 2500 kg/m³ respectively. Young's…

A: Glass fiber is denoted by 1 and Aluminum is denoted by 2 then According to the given data E1=85 Gpa…

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: B- Determine the points of the solution area for the problem shown in the figre and then find the…

Q: The force-couple system (System 1) as shown below is to be replaced by an equivalent system (System…

A: The given system 1 is The angle θ is θ=tan-1512θ=22.62°

Q: Two mutually exclusive alternatives are being considered. Alternative A has an initial cost of $100…

A: Dear Students

Q: 45° lz Yo,

Q: Two forces FA =185 lb and FB =189 lb are acting on the bracket shown with axes x,y,v and w…

Q: A2.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

Q: The post weighing 1500 lbs is to just be vertically pulled out of the ground using two ropes as…

Q: A four bar linkage have the following dimensions. Fixed Link AD = 4m, Driving Link AB = 1.5m, Driven…

Q: Simplify the following expressions (note that dj is the Kronecker delta, repeated index means…

A: To solve these expressions, use the definition of the Kronecker delta, which is a mathematical…

Q: Compute for the moment of inertia about xo and yo of the a) b) 100 mm 75 mm 25 mm 75 mm | = 11 - 12…

A: According to guidelines first will solve in multiple questions given

Q: 500 Gu Delermine the moment a bout Point (0) 610 as Shown

Q: SOLVE FOR THE RESULTANT OF THE FORCES. (NOTE: ALSO CALCULATE 0) 150N BONK

Q: A hole is to be punched out on a layer of papers using a puncher with a hole diameter of 100 mm. If…

Q: Solve using characteristics of equations. 5. у" + 14y' + 49у 3D 0%;B у(-4) %3 -1; у'(-4) 3D 5

Q: the force of system shown in the figure below, determine the resultant and locate with respect to…

A: For solution refer below images.

Q: supply as shown in A 5-cm galvanized steel Pipe the figure below. The pipe is 20 m long and has two…

A: To obtain the exit velocity of the water from the pipe outlet, we must apply the Bernoulli's…

Q: If an object is moved a distance D in the direction of an applied constant force F, then the work W…

Q: A young man, 22 years old, graduated from college and got his first job. He wants to have a…

Q: Solve the problem. A 11-in. connecting rod in an engine connects the wrist pin of a piston at point…

Q: Solve For the muximum value OF that pre vents the bar AP 50 kN. From moving if it weighs B P Am

Q: An engine drives a machine. The torque equations is given below. The moment of inertia of the…

A: Write the given data with suitable variables: I=54 kg-m2N=300 rpmθperiodθp=2π

Q: Determine the reaction force acting on the pin at A as the vector, if the beam AB has a mass of 100…

Q: 18 k 1. Solve the Concurrent Force system: 26 ngle

A: Given:

Q: Q1) calculate resultant force to the forces in figure (F1, F2,F3 and F4) IF Fir60N F4-20 slope of F4…

Q: Solve for the point A, B, C AND D. MAKE SURE THAT YOUR FINALS ANSWERS ARE IN 4 DECIMAL PLACES

Q: Find the resultant force from adding F1 + F2 + F3 where F1 = 160 lbs at 45 degrees F2 = 90 lbs…

Q: Refer to the figure below and solve for the linear velocities (ft/s) of all the points on the Jse…

Q: 400 lb y 300 lb 600 450 30°t 200 lb

A: Given Three force component and corresponding angles are given. Find The resultant force, F

Q: 1.2 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: **Question 3: Visit the parameters and change the option attributeSelectionMethod to "No Attribute…

Concept explainers

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.

Question

Solve show solution

A multiple-disk clutch is to operate in oil and be able to transmit a design
overload torque of 800 N m. The disks are alternately high-carbon steel
and molded asbestos, with inside and outside diameters of 90 and 150 mm,
respectively. Design values based on test experience for this application
are Pmax = 1000 kPa and f = 0.10. What total number of disks is required?
Also, what minimum clamping force is required to transfer this torque
through the clutch?
Ans. (8 Molded Asbestos Friction Disks and 9 High-Carbon Steel Plates) Note:
The number of friction interface surfaces: N = 16.
FClamping 8333 N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given:

VIEW

Step 2: Finding total number of disk required:

VIEW

Step 3: Finding the minimum clamping force required to transfer this torque:

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Clutches, Brakes, Couplings and Flywheels

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve in 15 min
An engine turns at 250 revolutions per minute and its stroke is 450 mm. Find the average pistol speed in meters per minute, and the speed of the centre of’ the crank pin in meters per minute.
Please solve only 1 and 2
Please give proper rough sketch with dimensions and try to solve within 20 minutes
If B=650 N Solve for: •Line of action of the Resultant Force •Horizontal and Vertical Force on each member •Gripping Force P •Magnitude of the Resultant Force -Include direction (upward, downward, N, E, W, S, or if Tensile or Compressive -Include 4 decimal points -Provide a readable solution
Please solve only 3 and 4
i need the answer quickly
Make it simple,Urgent.
And also solve for the direction and put a conclusion after getting the answer. Make sure that the answers are in 4 decimal places
pivot X 30° F As shown in the diagram above (viewed from above), force F of magnitude 882 N is exerted on a rod which is pivoted about its center a distance 0.7 from the pivot. Calculate the torque exerted by force F. Express your answer in N*m and round to the nearest tenth (1 decimal). Enter a negative answer for a clockwise torque and a positive answer for a counterclockwise torque.
5.3 Please help. Written on paper not typed on computer or keyboard please. Need help both questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
Show complete solution step by step