QUESTION 3In an axial clutch, the clutch plate has an outer diameter of 15.0 inches and an inner diameter of 5.0 inches. Assume a coefficient of friction of0.22. Applying the uniform wear assumption, what is the magnitude of the axial force (in lbf) to obtain a cluiching torque of 2000 in-lb?OA. 1.6x103OB. 1.7×103OC 1.8×103OD.2.1×103OE. None of the above

Given data Outside diameter of clutch plate, do=15 inInside diameter of clutch plate, di=5…

In an axial clutch, the clutch plate has an outer diameter of 15.0 inches and an inner diameter of 5.0 inches. Assume 0.22. Applying the uniform wear assumption, what is the magnitude of the axial force (in lbf) to obtain a cluiching tor OA 1.6×103 OB.1.7×103 OC. 1.8×103 OD.2 1x103

In an axial clutch, the clutch plate has an outer diameter of 15.0 inches and an inner diameter of 5.0 inches. Assume 0.22. Applying the uniform wear assumption, what is the magnitude of the axial force (in lbf) to obtain a cluiching tor OA 1.6×103 OB.1.7×103 OC. 1.8×103 OD.2 1x103

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A) If we consider a transmission ratio 1 to 5, in the arrangement of pulleys shown. and the tangential speed in the shaft (diameter of 30mm) where the driving pulley is coupled is 1.5 m/s. What is the rotational speed of the driven pulley (in rpm)? B) From the previous exercise. What is the length of the transmission band (belt) calculated in the previous exercise? Motriz 0.30 m 1.5 m uc=0.35 -0.30 m- 0.40 m Movida -0.30 m 0.30 m d=0.10 m e-0.05 m
An engine system of 3 msin components in a series sll having the same reliability. Determine the level of reliability required for each of the components if the engine is to have a reliability of 0.995. Round answer tob4 decimal places e.g. 15.2512
QUESTION 1 A suitable factor of safety to apply when selecting the cable for a factory hoist is: 05 O1.2 0.2 O 25 QUESTION 2 A winch drum of diameter 199mm turning at 14rpm lifts a load of 5.5kN. What is the winch output power? Give your answer in W to 1 decimal place without units eg 102.3 NOT 102345239 W QUESTION 3 The figure below shows two proposed designs of drums to solve the same load and line speed lifting arrangement. What is the biggest advantage with design A: A The torque on the drum shaft will be lower O The rope speed will be lower The bending moment in the drum shaft will be lower O The weight of the drum material will be less 刚 B
Please find the torque.
5) Which statement is true about the friction factor in the Moody diagram (shown below). Moody Diagram 0.1 0.09 Transition Region 0.08 0.07 0.05 0.04 0,06 0.03 0.05 0.02 0.04 0.015 0.01 0.03 0.005 0.002 0.001 5x10-4 2x10-49 10-4 5x10-5 10-5 5x10-6 10-6 Friction Factor 12---- Laminar Flow 64 Material Concrete, coarse 0.25 0.025 Concrete, new smooth Drawn tubing 0.0025 Glass, Plastic Perspex 0.0025 Iron, cast 0.15 Sevens, old 3.0 0.1 Steel, mortar lined Steel, rusted 0.5 Stoel, structural or forgod 0.025 Water mains, old Friction Factor=AP. 1.0 Smooth Pipe 3000 10³ 10¹ 105 106 107 108 Reynolds Number, Re - Vd P a) The lines for different relative roughness in the turbulent regime correspond to Darcy-Weisbach model b) The lines for different relative roughness in the turbulent regime correspond to Nikuradse model c) The lines for different relative roughness in the turbulent regime correspond to Hazen-Williams model d) The lines for different relative roughness in the turbulent regime…
Must solve all 3 questions. Dont solve only 1.
Please explain why it has .25 in the formula thanks
QUESTION 31 A multi-cylinder engine is to run at a constant load with an average speed of 600 rpm. The magnitude of the areas above and below the mean torque line are as follows: +2096, -2253.2, +2200.8, -2502.1, +2580.7, -2122.2 The speed fluctuation is 2% and moment of inertia of the machine is 60 kg.m² a) Calculate the necessary moment of inertia of the flywheel. b) The maximum and minimum speed throughout a cycle a) Determine suitable dimensions for cast iron flywheel. The density of cast iron is 7250 kg/m³, and its mass is 143.5 kg.
please assist with question 4
8.a. When a machine is tested, the volume of cooling air is 1250 cfm. If the temperature of the entering air is 25 C and the temperature of the outgoing air is 35 C, the loss in the machine isA. 7.1 kw.B. 24.8 kw.C. 12.5 kw.D. 17.7 kw. 8.b. When a motor is tested with a prony brake, the scale reading is 3.50 lb. The length of the brake arm is12 in. and its weight is 0.50 lb. If the motor speed is 1700 rpm and the power input is 1050 watts, themotor efficiency isA. 80.5%B. 69%C. 75%.D. 64.5%.
what should the torque speed graph look like? and what other aspects should be taken into account. DO NOT USE AI TO ANSWER
Q) Derive the expressions for the torque transmitting capacity of a single plate clutch by pressure