A multiple disc clutch has radial width of the friction material as 1/5th of the maximum radius. The coefficient of friction is 0.25. Find the total number of discs required to transmit 60 kW at 3000 r.p.m. The maximum diameter of the clutch is 250 mm and the axial force is limited to 600 N. Also find the mean unit pressure on each contact surface.

A multiple disc clutch has radial width of the friction material as 1/5th of the maximum radius. The coefficient of friction is 0.25. Find the total number of discs required to transmit 60 kW at 3000 r.p.m. The maximum diameter of the clutch is 250 mm and the axial force is limited to 600 N. Also find the mean unit pressure on each contact surface.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Question 3 An engine of a 2 ton truck develop 30 kW at 600 rpm. The truck is fitted with a cone…

A: For answer refer the next page.

Q: 300 rpm. The coefficient of friction between the belt and the pulley is 0.26, angle c lap 160° and…

Q: Find the power transmitted by a belt running over a pulley of 500mm diameter at 300 rpm. The…

A: It is the very basic problem of machine design and the topic is design of belt .

Q: A multiplate friction clutch is required to transmit 72 kW at 3600 r.p.m. The plates are alternately…

A: Given data: - The power transmitted by the clutch is P = 72 kW. The speed of the clutch is N =…

Q: .A centrifugal clutch has four shoes which suae i the driving shaft and make contact with the…

A: Given: The number of shoe, n = 4 The clearance , c = 5 mm = 0.005 m The internal diameter of the…

Q: Find the value of coefficient friction if friction force is 222 N and Normal force is 1000 N

Q: Two identical pulleys with diameter of 711 mm, are mounted on two parallel shafts for flat belt…

Q: Determine the given question with correct solution

A: Given data; P=25 KW=25×103 WN=300rpmp=85 KN/m2=0.85 N/m2d2=380 mmr2=190 mmn=2μ=0.25 Find,1.outer…

Q: A DC brushed motor has a no-load speed of wo and a stall torque of Ts. a. What is its peak power…

A: a.Here,T(ω)=Ts-TsωoωP(ω)=T(ω).ω=ωTs-ω2ωoTsNow,dP(ω)dω=Ts-2ωωoTs=0⇒ω=ωo2At…

Q: An automobile single plate ciutch consists of a pair of contacting surtaces. The inneOr and outer…

Q: Q2 ) A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has a face angle of 10° The width of…

A: Given, Power transmitted , P =10 Kw Speed, N =600 rpm Cone angle = 10 degree maximum pressure , Pr…

Q: Find the value of coefficient friction if friction force is 222 N and Normal force is 1000 N

A: Given data : Friction force=f Normal force=F' Required : Coefficient of friction

Q: Find the friction force if coefficient of friction 0.3 and normal force is 120 N

A: Given data : Coefficient of friction=μ Normal force=N To find : Friction force

Q: A flat belt is wrapped around a Ø3.00-inch pulley for 217°. The loose side belt tension is 282 lb…

Q: (A) If the power losses in Pelton wheel due to bucket friction is given by 1 POK (V, -u) where K is…

Q: A disc clutch is required yo transmit 5 kW at 2000 rpm with coefficient of friction 0.25 and bore…

A: Given Power, P = 5 kW Coefficient of friction = 0.25 Constant pressure, P = 1…

Q: Two parallel shafts whose centre lines are ‘5’ m apart, are connected by an open belt drive. The…

A: C=5 mD=3 md=3 mTmax=4 KNμ=0.3N=700 rpmVelocity of belt, V=π*d*N60V=π*3*70060=109.95 m/s

Q: A single-plate clutch has a friction disc with inner and outer radii of 20 mm and 40 mm,…

A: Uniform pressure theory is when the product of pressure and area of the contacting surface…

Q: The disc clutch has a pair of mating friction surfaces, with an outer diameter of 350 mm and an…

A: Given data:- outer diameter=350 mm inner diameter =250 mm The average value of the coefficient of…

Q: Q. A multi disc clutch has 5 plates having four pairs Myd of active friction surfaces. If the…

A: The solution is given in next step

Q: An open belt connects two flat pulleys. The pulley diameters are 300 mm and 450 mm and the…

A: Given data as per question d=300 mmD=450 mmθ=160×π180=2.79 radμ=0.35N=200 rpmp=3kw=3000…

Q: ch. The friction lining has a ce 25. The bore radius of friction li ilom contLacl pressur of IMI

Q: (i) A uniform ladder of length 7 m rests against a vertical wall. It makes an angle of 45° with the…

A: Q. 3(i), Given: Length of the ladder=7 m angle=45o coefficients of friction between the ladder and…

Q: The hand brake of Fig. is used to control the rotation of a drum. The coefficient of friction…

A: Given: The torque on the drum, T = 5 ft.lb The coefficient of friction between belt and drum, μ =…

Q: A pulley system uses four v-section belts each with a cross-sectional area of 700mm 2, an included…

A: The maximum force (tension) in the belt can be given as - T1 = 3×Centrifugal force500 =…

Q: Q2 ) A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has a face angle of 10 The width of…

Q: A cone clutch has D = 16 in, d = 14 in, a cone length of 3 in, and a coefficient of friction of…

Q: A friction clutch is to transmit 10 kW at 3000 rpm. It is to be of single plate type with both sides…

Q: An automobile single plate clutch consists of a pair of contacting surfaces. The inner and outer…

A: Uniform pressure theory: When the clutch and bearing mating components are fresh, the contact…

Q: Exomple: An automotive single-plate clutch with o pairs of frichon Surfaces, tvansmits a 300. N-m…

A: For single plate clutch : Torque (T)=300 N-m speed (N)= 1500 rpm inner dia.(d) = 170 mm outer…

Q: A single cylinder engine running at 2200rpm develops a torque of 8N-m. The indicated power of the…

A: The performance of any engine is described by its efficiency. There are mainly five types of…

Q: (i) The diameters of pulleys; (ii) The length of the belt and (iii) Belt tensions on the tight and…

Q: The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12…

Q: À conical pivo of pressure is the diameters the coefficient

A: Given data:

Concept explainers

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.

Question

A multiple disc clutch has radial width of the friction material as 1/5th of the maximum radius. The
coefficient of friction is 0.25. Find the total number of discs required to transmit 60 kW at 3000 r.p.m.
The maximum diameter of the clutch is 250 mm and the axial force is limited to 600 N. Also find the
mean unit pressure on each contact surface.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Clutches, Brakes, Couplings and Flywheels

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A CONE CLUTCH WITH CONE ANGL€ 20 IS TO TRANSMIT 7.5KW AT 750 8 P.m. THE NORMAL IN TENSITY OR PRESSURE BETWEEN THE CONTACT CACES IS NOT T O EXCEED 0-12N Imm? THE COEFEICIENT OF FRICTI(ON IS 0.2.1E FACE WID TH IS TH OF MEAN DIAMETER, FIND a) THE mAIN DIMENSIONS OF CLUTH AND (b) AXIAL FORCE REQUIRED whILE RUNNING
;: . L The contact surfaces in a cone clutch have an ej'fective diameter of 7‘5 i semi-angle of the cone is 15°. The coefficient of friction is 0.3. Find the torque requiy, 5 e slipping of the clutch if an axial force applied is 180 N. This clutch is employed to connect an electric motor running um_'form!y at 1 000 Epm. with, el which is initially stationary. The flywheel has a mass of 13.5 kg and its radius of gyriy, is Calculate the time required for the flywheel to attain full speed and also the energy [y, in of the clutch.
A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt and pulley is 0.3, semi V-groove angle is 22.5 degree and angle of contact of belt with the pulley is 160 degree. Ifthe mass of the belt is 0.45 kg/m and if permissible pull in the belt is 800 N. Calculate the power.(Consider the centrifugal tension in the belt.)
Q2/ A conical clutch an included angle of 60°. the outer radius and inner diameters are 80 and 20 cm respectively. Calculate the maximum and minimum intensity of pressure and force required to press the two halves together if it is to transmit 20 MW, at 60 rev/h. the coefficient of friction is 0.3, Use both the uniform wear theory and the uniform pressure theory.
Q1 Q5) Determine the principal dimensions of a cone clutch faced with lather to transmit 40 kW at 800 r.p.m. from an electric motor to an air compressor. Sketch a sectional front view of the clutch and provide the main dimensions. Assume that the semi-angle of the cone is 10°, the coefficient of friction is 0.3, mean diameter of cone is (7-10)d, where d is the diameter of the shaft, allowable normal pressure for lather and cast iron is 0.1 to 0.2 N/mm, shear stress 100 N/mm, load factor is 2 and the mean diameter to face width ratio is 6.
A multidisk clutch is required to have a torque capacity of 300 N.m. Due to space limitations, the inner and outer diameters are specified to be 62 mm and 128 mm respectively. The coefficient of friction is 0.30 and the limiting pressure for the friction material is 900 Pa. Find the minimum number disks using uniform-wear model. Please be clear on your solution!
A block brake with a torque of 250 N-m. Its drum rotates at 100 rpm. The length of the block (1) is twice its width (w). Assume, the coefficient of friction P is 0.35. Calculate: (1) the applied load (P) and the hinge-pin reaction (Rx ana Ry) for clockwise rotation of the drum; (2) the applied load and hinge-pin reaction for anticlockwise rotation of the drum; (3) the rate of heat generated during the braking action. (4) The dimensions of the block, if the intensity of pressure between the block and brake drum is 1 MPa. (5) Check whether the brake is self-locking.
A clutch functions to continue the power of 110 Hp and 3600 rpm rotation, number of clutch plate 1, The total force of the spring suppressor 1500 N, correction factor 0.95 and friction coefficient 0.3 Calculate the Measures of Do and Di if the ratio of Do: Di = 3: 2