A multi-plate clutch has four pairs of frictional surfaces, each of internal diameter 120 mm and external diameter 200 mm. If the coefficient of friction is 0.3 and the uniform pressure condition can be assumed, what is the required spring force when the plates transmit 20 kW at 1400 rpm?

A multi-plate clutch has four pairs of frictional surfaces, each of internal diameter 120 mm and external diameter 200 mm. If the coefficient of friction is 0.3 and the uniform pressure condition can be assumed, what is the required spring force when the plates transmit 20 kW at 1400 rpm?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The 60° V-belt of a machine is pass around the pulley A of a motor and over a pulley B as shown in…

Q: An elevator type lift is being designed to raise a load up to 5,000pounds between floors. Two…

A: Load to be raised : 5000 pounds Diameter of the screw threads 1.5 in Weight of the elevator is 800…

Q: A multiplate friction clutch is required to transmit 72 kW at 3600 r.p.m. The plates are alternately…

A: Given data: - The power transmitted by the clutch is P = 72 kW. The speed of the clutch is N =…

Q: .A centrifugal clutch has four shoes which suae i the driving shaft and make contact with the…

A: Given: The number of shoe, n = 4 The clearance , c = 5 mm = 0.005 m The internal diameter of the…

Q: Please don't provide handwritten solution .....

A: Given - Explanation - Image -1 Image -2 Hope you Understand. If any Query let me know. Thank You.…

Q: The tension in a pulley belt is 300 N when stationary. The smaller pulley has a diameter of 300 mm…

Q: (b) A single plate clutch has a driven plate with an annular friction lining of 380 mm outside…

A: Given: Outside diameter, D = 380 mm or 0.38 m Inside diameter, d = 270 mm or 0.27 m Pressure, P =…

Q: An automobile single plate ciutch consists of a pair of contacting surtaces. The inneOr and outer…

Q: solve show solution

Q: b) An automotive clutch driven plate is clamped between a fly- wheel and a sprung pressure plate.…

A: A clutch is a device that allows two parts with a shared axis of rotation to connect and disengage…

Q: l-plate clutch must transmit 23 kW of power without slipping at 2500 rev/min. The coefficient of…

Q: A single plate cutch consists of one pair of contacting surfaces. The inner and outer diameters of…

A: Given Data Inner diameter of clutch is: di=100 mm=ri=50 mm Outer diameter of clutch is: do=150…

Q: The effective pressure on a 400 mm diameter piston is 1.1 MN/m² when the crank is 32° beyond top…

A: Given: Diameter of the piston→D=400 mm=0.4 m So area of the piston→A=π4×D2=π4×0.42=0.125 m2 Pressure…

Q: Using the provided information, compete the following problems. • The system shown is in static…

A: Given:- = surface density of solar A = area The gravitational pulls…

Q: The disc clutch has a pair of mating friction surfaces, with an outer diameter of 350 mm and an…

A: Given data:- outer diameter=350 mm inner diameter =250 mm The average value of the coefficient of…

Q: Q. A multi disc clutch has 5 plates having four pairs Myd of active friction surfaces. If the…

A: The solution is given in next step

Q: The clutch of a motor car is required to transmit 9 kW at 3500 rpm. It is of single-plate type, with…

A: Given: The power of the motor is 9 kW. The coefficient of friction is 0.25. The maximum pressure is…

Q: An open belt connects two flat pulleys. The pulley diameters are 300 mm and 450 mm and the…

A: Given data as per question d=300 mmD=450 mmθ=160×π180=2.79 radμ=0.35N=200 rpmp=3kw=3000…

Q: Determine the minimum applied force P required to move wedge A to the right. The spring is…

Q: The tension in a pulley belt is 300 N when stationary. The smaller pulley has a diameter of 300 mm…

A: Introduction In this problem, we will calculate the tension on each side of the belt and the power…

Q: (i) A uniform ladder of length 7 m rests against a vertical wall. It makes an angle of 45° with the…

A: Q. 3(i), Given: Length of the ladder=7 m angle=45o coefficients of friction between the ladder and…

Q: A car engine has its rated output of 16 kW. The 2 maximum torque developed is 120 N-m. The clutch…

A: Given data as per the question power of car engine =16 kwMaximum torque developed =120 N.maxial…

Q: The hand brake of Fig. is used to control the rotation of a drum. The coefficient of friction…

A: Given: The torque on the drum, T = 5 ft.lb The coefficient of friction between belt and drum, μ =…

Q: A flat belt is required to transmit 35 kw from a pulley of 1.5 m effective diameter running at 300…

A: Given:P=35 KWd=1.5 mN=300 rpmθ=1124*2πμ=0.3t=10 mm

Q: The three flat blocks are positioned on the 30° incline as shown in Figure WDG – 3F, and a force P…

A: Approach to solving the question : Part A - The normal force between the 50-kg and 40-kg blocks will…

Q: A leather-faced cone clutch has a contact surface with a mean diameter of 15 in. and transinits 20…

A: Given: Mean diameter, dm = 15 in or 1.25 ft Power transmitted, P = 20 hp or 11000 lb.ft/s Rotational…

Q: The block A and the wedge B weighs 100 kN and 40 kN, respectively. The coefficient of friction for…

A: Write the given values along with suitable variables.

Q: The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction…

A: Given, Coefficient of friction, μ=0.15 Weight of the handle, W=15 N Applied force to the end of the…

Q: The tension, Tiial of V-belt with groove of 60° during initial adjustment is 150 N on each side. The…

A: Given Data: Tinitial =150NGroove angle α = 60°Angle of lap θ = 165°Coefficiet of friction μ =…

Q: Problem # 10: A horizontal bar, 11 ft long and of negligible weight, rests on rough inclined planes…

A: Given; The length of bar, L = 11 ft The coefficient of friction, f = 0.27

Q: The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction…

A: First, draw the free-body diagram of the handle: Now write the moment equation about the point 'O'…

Concept explainers

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.

Question

2 (b)
A multi-plate clutch has four pairs of frictional surfaces, each of internal diameter 120 mm and
external diameter 200 mm. If the coefficient of friction is 0.3 and the uniform pressure
condition can be assumed, what is the required spring force when the plates transmit 20 kW at
1400 rpm?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Expression of frictional torque in case of multi-plate clutch.

VIEW

Step 2 Calculation of spring force.

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Clutches, Brakes, Couplings and Flywheels

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A car has hydraulically operated disc brakes at the front and drum brakes at the rear. The frontbrakes have pistons of 58 mm diameter each, whereas each of the wheel cylinder at the rearbrake has 28 mm diameter. The master cylinder piston has diameter of 40 mm. The brake footpedal has a leverage of 4. If the brake pedal is applied a force of 100 N, Calculate (i) The brakingforce on the front axle, (ii) The braking force on the rear axle.
8. A cross belt arrangement has centre distance between pulleys as 1.5 m. The diameter of bigger and smaller pulleys are 'D' and 'd' respectively. The smaller pulley rotates at 1000 r.p.m. and the bigger pulley at 500 r.p.m. The flat belt is 6 mm thick and transmits 7.5 kW power at belt speed of 13 m/s approximately. The coefficient of belt friction is 0.3 and the density of belt material is 950 kg/m³. If the permissible tensile stress for the belt material is 1.75 MPa, calculate: 1. Diameters of pulleys; 2. Length and width of belt. [Ans. 500 mm, 250 mm ; 4.272 m, 90 mm]
The figure shows a system with a block m1 attached to a simple square thread screw with a mean diameter of 10 mm, a pitch of 3 mm and whose coefficient of static friction on the thread is 0.35. Block m1 is attached to block m2 by a rope, each of blocks m1 and m2 have a mass of 4 kg.Block m2 is in turn attached to a 15-kg block W by another rope, which passes over a static drum where the coefficient of static friction is 0.20. Determine the required Moment M that must be applied to the screw to start lifting block W. The coefficient of static friction between the surface and blocks m1 and m2 is 0.25. Need free body diagrams
What is the formula?? What is the answer??? Need help asap please
The coefficient of static friction under the block a and b are the same. If the block is in the verge of sliding, find the tension at each chord. Assume that the pulley is frictionless.Recall [from Physics]:?? = ???Where:?? - is the frictional force?? - is the normal force? -coefficient of static frictiona. Determine the tensile force (lb) on the cable 1.b. Determine the tensile force (lb) on the cable 2. Plsss show complete handwritten solution. Thanksss!!
A block brake with a torque of 250 N-m. Its drum rotates at 100 rpm. The length of the block (1) is twice its width (w). Assume, the coefficient of friction P is 0.35. Calculate: (1) the applied load (P) and the hinge-pin reaction (Rx ana Ry) for clockwise rotation of the drum; (2) the applied load and hinge-pin reaction for anticlockwise rotation of the drum; (3) the rate of heat generated during the braking action. (4) The dimensions of the block, if the intensity of pressure between the block and brake drum is 1 MPa. (5) Check whether the brake is self-locking.
Machine Elements
...A plate clutch with single driving plate with contact surfaces on each is required to transmit 35 kW at 2400 rpm. Given that μ = 0.29, R = 1.25r, Pmax = 0.2 MPa, determine the inside radius of the frictional surface in mm. Assume the uniform wear conditions.