Determine the minimum applied force P required to move wedge A to the right. The spring is compressed a distance of 175 mm. Neglect the weight of A and B. The coefficient of static friction for all contacting surface is us = 0.35. Neglect friction at the rollers. k = 15 kN/m- A O B 10°

Q: n an engine, the piston diameter is 3 1/4 inches, the stroke is 4 7/8 inches, and the piston…

A: For the solution refer below images.

Q: While taking a break from the Extreme Beer Fest in Boston, you decide to do something educational…

A: Draw the diagram for the given movements for a better understanding of the question and final…

Q: What kind of font is typical for usage in engineering diagrams?

A: To find: The type of font used in engineering diagrams.

Q: 0.2 m B 0.2 m 1.3 m 0.7 m A P Circular

A:

Q: the (1) two subscripts and (2) sign of the stress components (\sigma, \tau) under the given…

A: we have to define the state of stress for the given coordinate system

Q: 76°10' 0.500 DIA 45°00'- 1.125 DIA 1.000 0.875 Find length x in the accompanying figure.

A: Given figure can be redrawn as:

Q: 2 ft 2 ft 3 ft A 6 ft

A:

Q: Please show detailed solution in a handwritten format. Don't use chatgpt. Torque and Maximum shear…

A: Step 1: Step 2: Step 3: Step 4:

Q: In an engine, the piston diameter is 3 1/4 inches, the stroke is 4 7/8 inches, and the piston…

A:

Q: The bore diameter of each cylinder in a six-cylinder four-stroke petrol engine is 25 mm and the…

A:

Q: 06m For the above diagram, there are smooth journal bearings at supports A Band C. Given that y-1.2m…

A: F = 450 N M = 500 N y = 1.2 m

Q: The celebrated Lazydog has recently added a 81 m³ workshop on to his 3 house. What diameter must a 7…

A: Volume = 81 m3 Length = 7 m Time = 19 min. = 19 x 60 Sec Gauge pressure = 0.62 x 10-3 atm Viscosity…

Q: A gas has an initial temperature of 25 degrees Celsius. It is cooled until its temperature reduces…

A: final temperature = 22.5o CExplanation:Approach to solving the question: Detailed explanation:…

Q: Part A - Construction of Mohr's circle for the state of stress For the element shown, construct…

A: Given Data

Q: Interpret the significance of the letters shown in the illustration

A: Instruction given at tail of the welding symbol is "See detail A".Here detail A will have the…

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A: Step 1:a. Equation for the differential area aligned horizontally The differential area element dA…

Q: True Story! The 1998-1999 Mars Climate Orbiter mission was declared a total loss in 1999 as there…

A: The actual distance of orbiter from surface is .The distance taken of orbiter taken for calculation…

Q: 1.5 mm + 2.0 mm 2.0 mm 3.0 mm A shear force, S, is applied. This results in shear flow, shown with…

A: Shear flow at a junction is analogous to current at a junction. That is, the total amount of shear…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.