A cone clutch is to transmit 7.5 kW at 900 rpm. The cone has a face angle of 12o. The width of the face is half of the mean radius and the normal pressure between the contact faces is not exceeding 0.09Nmm2⁄. Assuming uniform wear and the coefficient friction between contact faces as 0.2. Find the main dimensions of the clutch and the axial force required to engage the clutch.

Q: Find the coefficient of friction Friction force=150 N Normal force=400 N

A: Given data : Friction force=F Normal force=N'   Required : Coefficient of friction

Q: A flat collar bearing has an external diameter which is 1.6 times the intenal diameter. The…

A:

Q: A multiplate friction clutch is required to transmit 72 kW at 3600 r.p.m. The plates are alternately…

A: Given data: -  The power transmitted by the clutch is P = 72 kW. The speed of the clutch is N =…

Q: Find the coefficient of friction Friction force=230 N Normal force=1200 N

A: Given data : Normal force=N' Friction force=f   Required : Coefficient of friction

Q: Find the value of coefficient friction if friction force is 222 N and Normal force is 1000 N

A:

Q: 17.4 the a-component f velocihy in The. h Laminar boundary dayen is given by 3 (Sme) %3D Ua OLt ain…

A: Given,UUo=32yδ-12yδ3 From the continuity equation,…

Q: The two square-jaw grips have the dimensions shown in the figure and are made of mild steel. The…

A: Power transmitted (P) = 1.8 kWRotational speed (n) = 600 rpmTo calculate:The surface pressure on the…

Q: From the rotating shaft shown below, a force 100 N was pulled to reduce the shaft’s angular speed…

A:

Q: A conical clutch has an included angle of 150. The outer and inner diameters are 100 and 40 mm…

A: Given data:Since, the clutch is of two halves.So, the cone angle of the clutch isOuter diameter,…

Q: plate clutches an included angle of 120°. A multi plate clutch, has 2 disc diameters 600 mm. The…

A:

Q: Q2 ) A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has a face angle of 10° The width of…

A: Given,  Power transmitted , P =10 Kw Speed, N =600 rpm Cone angle = 10 degree maximum pressure , Pr…

Q: Find the value of coefficient friction if friction force is 222 N and Normal force is 1000 N

A: Given data : Friction force=f Normal force=F'   Required : Coefficient of friction

Q: (A) If the power losses in Pelton wheel due to bucket friction is given by 1 POK (V, -u) where K is…

A:

Q: determine the diameter o

A: Given data; A shaft is supported on two bearings as shown in figure:length =1.5 mIf shaft is…

Q: Q. A multi disc clutch has 5 plates having four pairs Myd of active friction surfaces. If the…

A: The solution is given in next step

Q: The diagram below represents an elevator used to lift concrete blocks to upper levels on a…

A:

Q: A conical clutch has an inclined angle of 120. The outer and inner diameters are 80 mm and 20 mm…

A: The answer is given in the following step

Q: The clutch of a motor car is required to transmit 9 kW at 3500 rpm. It is of single-plate type, with…

A: Given: The power of the motor is 9 kW. The coefficient of friction is 0.25. The maximum pressure is…

Q: 3/ A multi- plate clutch is to transmit 12 kW at 1500 r.p.m. The inner and outer dii for the plates…

A: Given data as per the question Power transmitted =12 kw speed =1500 rpm spring force =1kN angular…

Q: Q6 Engine developing power at 1000rpm is fitted with a cone clutch having the face width of the…

A: To calculate the mean diameter of the cone clutch, developing power and the constructionspeed of the…

Q: A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has a face angle of 10◦ The width of the…

A: Given data:

Q: (i) A uniform ladder of length 7 m rests against a vertical wall. It makes an angle of 45° with the…

A: Q. 3(i), Given: Length of the ladder=7 m angle=45o coefficients of friction between the ladder and…

Q: The hand brake of Fig. is used to control the rotation of a drum. The coefficient of friction…

A: Given: The torque on the drum, T =  5 ft.lb The coefficient of friction between belt and drum, μ =…

Q: Given: Q=14,361.60gpm L=1000ft D=2ft hf=12.58ft. Determine the friction

A: Given     Discharge, Q = 14361.60 gpm = 0.91 m3/s         Length, L = 1000 ft = 304.8 m…

Q: Q2 ) A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has a face angle of 10 The width of…

A:

Q: A friction clutch is to transmit 10 kW at 3000 rpm. It is to be of single plate type with both sides…

A:

Q: Hth of the belt, nece 1600 r.p.m and th the angle of cont

A: given:P=7.5kwd=300mmN=1600rpmμ=0.22θ=210

Q: Q2/ A compound steam engine develops 250 kW at 80 r.p.m. The coefficient of fluctuation of energy as…

A: given data power= 250kw speed = 80rpm fluctuation of energy = 0.15 fluctuation of speed = 1% radius…

Q: 1 multi-plate disc clutch ransmits 55 KW of power

A:

Q: Exomple: An automotive single-plate clutch with o pairs of frichon Surfaces, tvansmits a 300. N-m…

A: For single plate clutch : Torque (T)=300 N-m speed (N)= 1500 rpm inner dia.(d) = 170 mm outer…

Q: An automobile single-plate clutch consists of a pair of contacting surfaces. The inner and outer…

A: Uniform Wear Theory: When the product of pressure and area of the contacting surface transmitting…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.