A cone clutch for industrial use is to transmit 15 hp at 400 rpm. The mean diameter of the clutch is 10 in. and the cone angle 10; let the coefficient of friction be 0.3 for the cast-iron cup and the asbestos-lined cone; permissible p = 35 psi. Compute (a) The needed axial force (b) The face width

Q: H.W (1): A single dry plate clutch transmits 7.5 kW at 900 r.p.m. The axial pressure is limited to…

A:

Q: A multi-disk clutch consists of two steel disks with one bronze disk. The inner and outer diameters…

A: Given data:

Q: Q1) The V thread of a screw jack has a single start with out side diameter 40 mm and 6 mm pitch. The…

A: There are two types of forces that are acting on a circular surface. One type of force is Radial…

Q: mm, The semi-angle of the cone is 15°. The coefficient of friction is 0.3. Find the torque required…

A: A disc or plate clutch has the same use that a cone clutch has. Instead of two spinning discs, the…

Q: Q2 ) A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has a face angle of 10° The width of…

A: Given,  Power transmitted , P =10 Kw Speed, N =600 rpm Cone angle = 10 degree maximum pressure , Pr…

Q: A single plate clutch, with both sides effective has outer and inner diameters 300 mm and 200 mm…

A:

Q: A multiple-disk clutch with 17 disks, 8 disks turning with one shaft and 9 with the other shaft, is…

A: To Find : The axial force required to transmit the rated torque and determine the pressure between…

Q: A local utility vehicle production company have considered using in one of its design a multi-disc…

A: Given data:- steel discs=9 bronze discs =8 outside diameter =220mm inside diameter =160mm Shaft…

Q: ch. The friction lining has a ce 25. The bore radius of friction li ilom contLacl pressur of IMI

A:

Q: A conical friction clutch is used to transmit 70 kW at 1000 rpm. The semicone angle is 20° and the…

A: To Find : The axial force Given : The transmit power  is The semicone angle is The inner diameter is…

Q: Given: Q=14,361.60gpm L=1000ft D=2ft hf=12.58ft. Determine the friction

A: Given     Discharge, Q = 14361.60 gpm = 0.91 m3/s         Length, L = 1000 ft = 304.8 m…

Q: The band wrench of Fig. an oil filter from a car. (The filter acts as if it were a wheel with a…

A: Free body diagram of the tensions on slack side and tight side To determine the minimum coefficient…

Q: A multi disc clutch transmits 55kW of power at 1800 rpm. Coefficient of friction for the friction…

A:

Q: A multiple disc clutch has radial width of the friction material as 1/5th of the maximum radius. The…

A: given : b = 15ro μ = 0.25 P = 60 kW @ 3000rpm do = 250 mm  so  ro = 125 mm W = 600 N   1) no.of…

Q: A multiple disc clutch is used to operate the speed regulating gears of lathe. If the torque…

A: Friction Force that resists the sliding or rolling of one solid object over another. Frictional…

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.