A turnbuckle is used to connect two rods, one having right handed and other, having left handed V-threads. The angle of V-threads is 60 degrees. The rods have a mean diameter of 2 cm and 3 threads per cm. The coefficient of friction between the rods and the nut connecting the rods is 0.15. Find the torque required on the nut to produce a pull of 4 kN. Assume that rods do not twist.

A turnbuckle is used to connect two rods, one having right handed and other, having left handed V-threads. The angle of V-threads is 60 degrees. The rods have a mean diameter of 2 cm and 3 threads per cm. The coefficient of friction between the rods and the nut connecting the rods is 0.15. Find the torque required on the nut to produce a pull of 4 kN. Assume that rods do not twist.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The roughly position of the automobile jack shown in the figure is a square screw with a single blade at both ends. ABC is controlled by a bolt (right-hand threaded in A, left-handed in C). square of the bolt screw has a pitch of 2.5 mm and an average diameter of 9 mm. between the bolt and the jack limbs The coefficient of static friction is 0.15, taking into account the position and load shown, you can use the jack Find the magnitude of the torque that must be applied to raise it.
Question 2 A aluminium wheel of diameter 200 mm carries a load of 800 N.If 200 N force required at center to roll the wheel. calculate the coefficient of rolling friction.
Find the coefficient friction at point A, assume there is no friction at point B.
(a) A body of weight 45 N is placed on a rough horizontal plane. To just move the body on the horizontal plane, a push of 25 N inclined at 11° to the horizontal plane is required. Find the coefficient of friction. (b) Determine the number of members in a structure, if the total number of joints in the structure is 3. Enter your student ID in the box and upload your handwritten answers in the separate link provided.
A steel tire, 20 mm thick, 90 mm wide, and 1600.0 mm inside diameter is heated and shrunk onto a steel wheel 1600.5 mm in diameter. If the coefficient of static friction is 0.40, what torque is required to twist the tire relative to the wheel? Neglect the deformation of the wheel. Use E = 100 GPa.
100 mm 200 mm GIVEN: Coefficient of static friction at A = 0.4 Collar at B is smooth and exerts horizontal force on pipe Mass of bracket is negligible ASK What is minimum distance x so bracket can support cylinder at any mass without slipping?
The root diameter of a triple threaded power screw is 550 mm It has a pitch of 10 mm It is used to lift a load of 15 kN. The collar of the screw has an outside diameter of 100 mm and an inner diameter 60 mm Find the force applied at a radius of 950 mm if the coeffcient of friction for both threads and collar is 0.20.
What is the formula?? What is the answer??? Need help asap please
A block brake with a torque of 250 N-m. Its drum rotates at 100 rpm. The length of the block (1) is twice its width (w). Assume, the coefficient of friction P is 0.35. Calculate: (1) the applied load (P) and the hinge-pin reaction (Rx ana Ry) for clockwise rotation of the drum; (2) the applied load and hinge-pin reaction for anticlockwise rotation of the drum; (3) the rate of heat generated during the braking action. (4) The dimensions of the block, if the intensity of pressure between the block and brake drum is 1 MPa. (5) Check whether the brake is self-locking.