In an engine governor of the Porter type, the upper and lower arms are 200 mm and 250 mm respectively and pivoted on the axis of rotation. The mass of the central load is 15 kg, the mass of each ball is 2 kg and friction of the sleeve together with the resistance of the operating gear is equal to a load of 24 N at the sleeve. If the limiting inclinations of the upper arms to the vertical are 30° and 40°, find, taking friction into account, range of speed of the governor.

In an engine governor of the Porter type, the upper and lower arms are 200 mm and 250 mm respectively and pivoted on the axis of rotation. The mass of the central load is 15 kg, the mass of each ball is 2 kg and friction of the sleeve together with the resistance of the operating gear is equal to a load of 24 N at the sleeve. If the limiting inclinations of the upper arms to the vertical are 30° and 40°, find, taking friction into account, range of speed of the governor.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12 Mpa. This is designed for a vehicle with 13kW power at a speed of 700 rpm. Assume uniform wear conditions and a friction coefficient of 0.25. If the outer dimater of the disc is 1.25 times the internal diameter, determine the dimensions of the disc lining and the axial force exerted by the springs.
An arrangement of three boxes is shown in figure below. Box A weighs 25 N and rests on an inclined plane, while box B weighs 50 N and rests on a horizontal plane. The coefficient of friction between box A and the inclined plane is 0.3, and between box B and the horizontal plane is 0.4. The pulleys are all frictionless. Determine the range of weight of box C for which no motion will occur. Consider both sliding and tipping of boxes A and B. 0.6 m 0.75 m 25 N 5 A 4 C pome 0.8 m 0.6 m 50 N B 1.2 m
two cylinders are connected to form a parallel cylinder actuatingsystem. Assume the bore and rod diameters of the left cylinder are 120 mm and 60 mm, respectively, and that those of the right cylinder are 100 mm and 50 mm. If the mass of the external loads to be driven by the left and right cylinders are 750 and 500 kg, respectively, and the back pressure in both rod-end chambers is 200 kPa, calculate the operating pressure of each cylinder for driving the loads. (Assume that the left cylinder requires 550 kPa for no-load extension and the right one requires 500 kPa.) If the supplying flow is 150 L ・ min−1, what are the extending velocities of those cylinders? Consider the friction and back pressure for the design Will those two cylinders extend simultaneously under the stated condition
The figure shows a system with a block m1 attached to a simple square thread screw with a mean diameter of 10 mm, a pitch of 3 mm and whose coefficient of static friction on the thread is 0.35. Block m1 is attached to block m2 by a rope, each of blocks m1 and m2 have a mass of 4 kg.Block m2 is in turn attached to a 15-kg block W by another rope, which passes over a static drum where the coefficient of static friction is 0.20. Determine the required Moment M that must be applied to the screw to start lifting block W. The coefficient of static friction between the surface and blocks m1 and m2 is 0.25. Need free body diagrams
A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt and pulley is 0.3, semi V-groove angle is 22.5 degree and angle of contact of belt with the pulley is 160 degree. Ifthe mass of the belt is 0.45 kg/m and if permissible pull in the belt is 800 N. Calculate the power.(Consider the centrifugal tension in the belt.)
The corediameter of the double start square threaded screw having a pitch of 12mm is 50 mm. A load of 18kN is lifted through a distance of 180mm. Find the work done(in Joule)in lifting the loadand the efficiency of the screw, when 1. The load rotates with the screw, and 2. The load rests on the loose head which does not rotate with the screw. The external and internal diameter of the bearing surface of the loose head are 60 mm and 10 mmrespectively. The coefficient of friction for the screw is 0.11,whilefor the bearing surface is 0.13.
A 90 kN locomotive, with a 16 km/hr initial speed, move up an incline. The locomotive has 6 pairs of drive wheels, having a diameter of 600 mm. If the incline angle is 7° and a 750 N-m torque is developed at each driving wheel, calculate the frictional force (in kN), neglecting the rotation energy of the drive wheels.
Two machines are coupled by means of a clutch plate with 2 contact surfaces. The plate has an inner diameter of 125 mm and an outer diameter of 200 mm and the coefficient of friction between mating surfaces is 0.35. It is assumed that shafts of both machines are co-axial and the driving shaft is rotating at a constant speed of 240 rev/min when it is suddenly brought in contact with the driven shaft/machine initially rotating at 20 rev/min. The Moment of Inertia of the driven machine is 21 kgm2. A slippage period of 6.8 sec is observed while the driven machine is brought to the full speed of the driving shaft. Analyse the frictional power transmission and calculate: The magnitude of the torque necessary to cause the described acceleration of the driven shaft :
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? dont write handwritten solution.