Determine the principal dimensions of a cone clutch faced with lather to transmit 40 kW at 800 r.p.m. from an electric motor to an air compressor. Sketch a sectional front view of the clutch and provide the main dimensions. Assume that the semi-angle of the cone is 10°, the coefficient of friction is 0.3, mean diameter of cone is (7-10)d, where d is the diameter of the shaft, allowable normal pressure for lather and cast iron is 0.1 to 0.2 N/mm, shear stress 100 N/mm², load factor is 2 and the mean diameter to face width ratio is 6.

Determine the principal dimensions of a cone clutch faced with lather to transmit 40 kW at 800 r.p.m. from an electric motor to an air compressor. Sketch a sectional front view of the clutch and provide the main dimensions. Assume that the semi-angle of the cone is 10°, the coefficient of friction is 0.3, mean diameter of cone is (7-10)d, where d is the diameter of the shaft, allowable normal pressure for lather and cast iron is 0.1 to 0.2 N/mm, shear stress 100 N/mm², load factor is 2 and the mean diameter to face width ratio is 6.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.76P: The clutch described in Prob. 7.75 is to transmit a torque of 120lbft when the total spring force...

See similar textbooks

Related questions

Q: A multiple-disk clutch is to operate in oil and be able to transmit a design overload torque of 800…

A: Given:T = 800 N-mDo = 150 mm = 0.150mDi = 90 mm = 0.09mpmax =1000 kPaf = 0.10To findTotal number of…

Q: ch. The friction lining has a ce 25. The bore radius of friction li ilom contLacl pressur of IMI

Q: i need the answer quickly

Q: A band brake having band-width of 80 mm, drum diameter of 250 mm, coefficient of friction of 0.25…

A: From the given data, useful data can be given by, Drum diameter = d = 250 mm = 0.25 m Coefficient of…

Q: A leather-faced cone clutch has a contact surface with a mean diameter of 15 in. and transinits 20…

A: Given: Mean diameter, dm = 15 in or 1.25 ft Power transmitted, P = 20 hp or 11000 lb.ft/s Rotational…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step by step

Solved in 8 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

I need the answer as soon as possible
A multi-disk clutch consists of two steel disks with one bronze disk. Theinner and outer diameters of the contacting surfaces are 200 and 250 mmrespectively. The coefficient of friction is 0.1 and the maximum pressurebetween the contacting surfaces is limited to 0.4 N/mm2. Assuming uniformwear theory, calculate the required force to engage the clutch and the powertransmitting capacity at 720 rpm
A multiple disc clutch has radial width of the friction material as 1/5th of the maximum radius. The coefficient of friction is 0.25. Find the total number of discs required to transmit 60 kW at 3000 r.p.m. The maximum diameter of the clutch is 250 mm and the axial force is limited to 600 N. Also find the mean unit pressure on each contact surface.
A cone clutch has cone elements at an angle of 12o. The clutch transmit 25 HP at a speed of 1200 rpm. The mean diameter of the conical friction section is 16 in and the coefficient of friction is 0.35. Find the axial force needed to engage the clutch.
A multiple V-belt drive is required to transmit 4 kW. The smaller pulley of the system is150 mm diameter, rotates at 200 rev/min, and has an angle of lap angle of 135°. Thegrove angle is 40° and the coefficient of friction between the belt and the pulleys is 0·3.If the maximum tension in any one belt is limited to 800 N, calculate:(a) The number of belts required. (b) The minimum tension in any one belt. (c) The required pre-tensioning of the belt. The centre-to-centre distance between the pulleys is 2 m.(d) Determine to the nearest mm, the required size for the larger pulley.(e) Find the approximate length of the belt
A multi-plate clutch has four pairs of frictional surfaces, each of internal diameter 120 mm and external diameter 200 mm. If the coefficient of friction is 0.3 and the uniform pressure condition can be assumed, what is the required spring force when the plates transmit 20 kW at 1400 rpm?
A leather faced cone clutch transmits power at 500 rpm. The semi-coneangle a is 12.5°. The mean diameter of the clutch is 300 mm, while the facewidth of the contacting surface of the friction lining is 100 mm. The coefficientof friction is 0.2 and the maximum intensity of pressure is limited to 0.07N/mm2. Calculate the force to engage the clutch and the power transmittingcapacity.
A cone clutch has an angle of 12 dgrees and coefficient of friction of 0.42. Find the axial forcerequired if the capacity of the clutch is 8 KW at 500 rpm. The mean diameter of the active conicalsections is 300 mm. Use uniform wear method.
Solve show solution
The figure shows an internal rim-type brake having an inside rim diameter of 300 mm and a dimension R 5 125 mm. The shoes have a face width of 40 mm and are both actuated by a force of 2.2 kN. The drum rotates clockwise. The mean coefficient of friction is 0.28. a. Find the maximum pressure and indicate the shoe on which it occurs. b. Estimate the braking torque effected by each shoe, and find the total braking torque. c. Estimate the resulting hinge-pin reactions. 30°- 30°. R 120° 120° Pin Pin 30° 30° Figure 3: An internal rim-type brake
Plz attempt if you know the answer otherwise skip to another expert. A flat belt is required to transmit 30 kW from a pulley of 1.5 m effective diameter running at 300 rpm. The angle of contact is spread over 11/24 of the circumference. The coefficient of friction between the belt and pulley surface is 0.3. Determine taking centrifugal tension in to account, width of the belt required. It is given that the belt thickness is 9.5 mm, density of belt material is 100 kg / (m ^ 3) and the permissible working stress is 2.5 MPa.
A V-belt from a 10-in. diameter grooved pulley that rotates at 1800 rpm, up to a 36-in. diameter flat pulley. The distancebetween axes is 40” and the throat angle is 40°. The coefficient of frictionbetween the belt and the grooved pulley is 0.2 and with the flat pulley it is also 0.2. Thecross section of the belts is a trapezoid with parallel sides of 1.5” and 0.75”, witha height between them of 1”. The weight of this strap is 0.04 lbf/in3, and the maximumAllowable tension on each belt is 200 lbf. Determine: a) How many straps arethey need. b) The Torque applied in the transmission, c) The Transmitted power.