A cone clutch has cone elements at an angle of 12o . The clutch transmit 25 HP at a speed of 1200 rpm. The mean diameter of the conical friction section is 16 in and the coefficient of friction is 0.35. Find the axial force needed to engage the clutch.

Q: The 60° V-belt of a machine is pass around the pulley A of a motor and over a pulley B as shown in…

A:

Q: An elevator type lift is being designed to raise a load up to 5,000pounds between floors. Two…

A: Load to be raised : 5000 pounds Diameter of the screw threads 1.5 in Weight of the elevator is 800…

Q: 3. A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt and…

A: Given data: - The speed of the belt is v = 1440 m/min. The friction coefficient between belt and…

Q: Question 3 An engine of a 2 ton truck develop 30 kW at 600 rpm. The truck is fitted with a cone…

A: For answer refer the next page.

Q: A multiplate friction clutch is required to transmit 72 kW at 3600 r.p.m. The plates are alternately…

A: Given data: -  The power transmitted by the clutch is P = 72 kW. The speed of the clutch is N =…

Q: Find the value of coefficient friction if friction force is 222 N and Normal force is 1000 N

A:

Q: A conical clutch has an included angle of 150. The outer and inner diameters are 100 and 40 mm…

A: Given data:Since, the clutch is of two halves.So, the cone angle of the clutch isOuter diameter,…

Q: mm, The semi-angle of the cone is 15°. The coefficient of friction is 0.3. Find the torque required…

A: A disc or plate clutch has the same use that a cone clutch has. Instead of two spinning discs, the…

Q: Find the value of coefficient friction if friction force is 222 N and Normal force is 1000 N

A: Given data : Friction force=f Normal force=F'   Required : Coefficient of friction

Q: A flat belt is wrapped around a Ø3.00-inch pulley for 217°. The loose side belt tension is 282 lb…

A:

Q: A disc clutch is required yo transmit 5 kW at 2000 rpm with coefficient of friction 0.25 and bore…

A: Given                      Power, P = 5 kW Coefficient of friction = 0.25  Constant pressure, P = 1…

Q: The effective pressure on a 400 mm diameter piston is 1.1 MN/m² when the crank is 32° beyond top…

A: Given: Diameter of the piston→D=400 mm=0.4 m So area of the piston→A=π4×D2=π4×0.42=0.125 m2 Pressure…

Q: A single-plate clutch has a friction disc with inner and outer radii of 20 mm and 40 mm,…

A: Uniform pressure theory is when the product of pressure and area of the contacting surface…

Q: The disc clutch has a pair of mating friction surfaces, with an outer diameter of 350 mm and an…

A: Given data:- outer diameter=350 mm inner diameter =250 mm The average value of the coefficient of…

Q: Determine the resulting torque of a uniform pressure frictional clutch having 4 discs in the driving…

A:

Q: An open belt connects two flat pulleys. The pulley diameters are 300 mm and 450 mm and the…

A: Given data as per question d=300 mmD=450 mmθ=160×π180=2.79 radμ=0.35N=200 rpmp=3kw=3000…

Q: ch. The friction lining has a ce 25. The bore radius of friction li ilom contLacl pressur of IMI

A:

Q: The hand brake of Fig. is used to control the rotation of a drum. The coefficient of friction…

A: Given: The torque on the drum, T =  5 ft.lb The coefficient of friction between belt and drum, μ =…

Q: A flat belt makes contact with an 16 in. diameter pulley through half its circumference. If the…

A: Given data:- Diameter of pulley =16 in Angle of contact θ =π the coefficient of friction μ = 0.45…

Q: The band of a brake has a contact angle of 18° deg. If the pulls on the bands are 275 kg and 100 kg,…

A:

Q: The band wrench of Fig. an oil filter from a car. (The filter acts as if it were a wheel with a…

A: Free body diagram of the tensions on slack side and tight side To determine the minimum coefficient…

Q: Exomple: An automotive single-plate clutch with o pairs of frichon Surfaces, tvansmits a 300. N-m…

A: For single plate clutch : Torque (T)=300 N-m speed (N)= 1500 rpm inner dia.(d) = 170 mm outer…

Q: The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12…

A:

Q: À conical pivo of pressure is the diameters the coefficient

A: Given data:

Q: Problem 5 900 N person Find the coefficient of friction at point A, assumed there is no friction at…

A: Let us draw the FBD Assume the weight of ladder and man will acts in COG

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.