A multi-plate clutch must transmit 11 kW of power without slipping at 1500 rev/min. The coefficient of friction is 0.3. The inner and outer radis are 30 and 85 mm respectively. The axial force applied to the plates is 780 N. Determine the number of plates required

Q: Prob # 9. Find the horsepower transmitted by a pair of friction wheels, the diameter of driving…

A:

Q: An elevator type lift is being designed to raise a load up to 5,000pounds between floors. Two…

A: Load to be raised : 5000 pounds Diameter of the screw threads 1.5 in Weight of the elevator is 800…

Q: Due to the force of magnitude magnitude 100N applied on the jockey pulley, the top of the slack side…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: .A centrifugal clutch has four shoes which suae i the driving shaft and make contact with the…

A: Given:  The number of shoe, n  = 4 The clearance , c = 5 mm = 0.005 m The internal diameter of the…

Q: An open belt connects two flat pulleys. The pulley diameters are 300 mm and 450 mm and the…

A:

Q: A block rest on a horizontal board. the board is gradually tilted upward and the block just begin to…

A: (a) μS is the coefficient of static friction between the block and the board.     ϕ is the limiting…

Q: 6. The radius pulley and shaft are 8-in and 1-in respectively. The shaft is supported by two journal…

A: Given:Radius of the pulley, r=8 inCoefficient of static friction, μs=0.15Coefficient of kinetic…

Q: THE ENGINE OF AN AUTOMOBILE IS RATED TO GIVE SOKWAT 200 RPM WITH A MAXIMUM TORQUE OF 600 N-M. DESIGN…

A: The answer is mention below

Q: solve show solution

A:

Q: 30 KN of force at one end just supports a weight of 30,000 KN load at the other end. If the rope is…

A:

Q: The wedge is used to level the member. The coefficient of static friction between the wedge and the…

A: Free body diagram is provided below

Q: The band brake of Fig is used to control the rotation of a drum. The weight of the handle is 2 lb.…

A: Draw the free-body diagram of the handle when the rotation of the drum is clockwise.

Q: b) An automotive clutch driven plate is clamped between a fly- wheel and a sprung pressure plate.…

A: A clutch is a device that allows two parts with a shared axis of rotation to connect and disengage…

Q: Q) A single plate clutch has to transmit 75 kW at 3000 r.p.m. The spring exerts an axial pressure of…

A: The answer is

Q: A flat belt is wrapped around a Ø3.00-inch pulley for 217°. The loose side belt tension is 282 lb…

A:

Q: 1.) Compute the weight of block B that will prevent the two block system from sliding. Block A…

A:

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: Given:The weight of the block B, The weight of the bracket A, The coefficient of static friction…

Q: An open belt connects two flat pulleys. The pulley diameters are 300 mm and 450 mm and the…

A: Given data as per question d=300 mmD=450 mmθ=160×π180=2.79 radμ=0.35N=200 rpmp=3kw=3000…

Q: Determine diameter of hand-wheel or length of handle, assuming that maximum force exerted by a man…

A: Given, Force exerted by a man, F=150lbf Force need to be applied, P=6000lbfCorfficient of…

Q: The 100 – Ib force acts as shown on a 300 – Ib block placed on an inclined plane. The coefficients…

A:

Q: If a piece of block weighing 150 kg is to be pulled up by a winch using two cables on a 25 deg…

A: Frictional force is formed when two surfaces attempt to move in the same direction or in opposite…

Q: hree identical blocks are placed on top of each other on a horizontal plane. Each block has a weight…

A: To determine the horizontal force that must be applied at the middle block without causing motion to…

Q: The tension in a pulley belt is 300 N when stationary. The smaller pulley has a diameter of 300 mm…

A: Introduction In this problem, we will calculate the tension on each side of the belt and the power…

Q: A car engine has its rated output of 16 kW. The 2 maximum torque developed is 120 N-m. The clutch…

A: Given data as per the question power of car engine =16 kwMaximum torque developed =120 N.maxial…

Q: 4. A óm ladder weighs 350 N is placed against a rough vertical wall. The angle between the ladder…

A:

Q: A leather-faced cone clutch has a contact surface with a mean diameter of 15 in. and transinits 20…

A: Given: Mean diameter, dm = 15 in or 1.25 ft Power transmitted, P = 20 hp or 11000 lb.ft/s Rotational…

Q: While a vehicle with a mass of 2350 kg is moving at 120 km/h, suddenly braking It stops with an…

A:

Q: 6. The radius pulley and shaft are 8-in and 1-in respectively. The shaft journal bearings. The…

A:

Q: A flat belt makes contact with an 16 in. diameter pulley through half its circumference. If the…

A: Given data:- Diameter of pulley =16 in Angle of contact θ =π the coefficient of friction μ = 0.45…

Q: The band of a brake has a contact angle of 18° deg. If the pulls on the bands are 275 kg and 100 kg,…

A:

Q: Problem # 10: A horizontal bar, 11 ft long and of negligible weight, rests on rough inclined planes…

A: Given; The length of bar, L = 11 ft The coefficient of friction, f = 0.27

Q: The band wrench of Fig. an oil filter from a car. (The filter acts as if it were a wheel with a…

A: Free body diagram of the tensions on slack side and tight side To determine the minimum coefficient…

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.