Answered: 6O cm 20.0m 20cm 20 Cm CIOSS - section

Engineering

Civil Engineering

6O cm 20.0m 20cm 20 Cm CIOSS - section

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: curved-beam formula to compute the bending stress.

Q: f the bending stress at section 2-20 MPa. What are the bending stresses at sections 1, 3, and 12 mm…

Q: The rod has a diameter of 40 mm. It is subjected to the force system Fx=1300 N=1300 N, Fy=500 N=500…

A: The diameter of the rod, D = 40mmThe force at the free end, Fx=1300 N, Fy=500 N, Fz=800 N The rod is…

Q: *8-72. The hook is subjected to the force of 80 lb. Determine the state of stress at point A at…

A: Given :

Q: Solve the magnitude of the bar force of members AD, BD, CD, and CE and identify the type of stress…

A: Given: A simply supported truss with hinge support at A and roller support at F. W=134 kN To…

Q: er must exert a force of P 3800 lbs at B as shown. The lever lengths are a= 11.5 in. ar or the lever…

A: Section modulus is z=Mσz=31734.518 lb-in10500 psiz=3.0223in3

Q: Q1:- At a certain point on the outside of a shaft, which is subjected to a twisting moment (torque)…

Q: 4) A simply supported box beam is constructed using 4 pieces of 50 x 200 glued together supports the…

A: Size of pieces = 50 × 200 mm

Q: The internal shear force V at a certain section of an aluminum beam is 10.2 kN. If the beam has the…

A: Solution:

Q: 200 mm If the beam is subjected to a bending moment of M=50KN, determine the maximum bending stress…

A: Using formula to find bending stress

Q: For the cantilever beam shown. find the value of Normal stress due to axial :load at point A 4 KN 6…

A: ASKED: To compute the normal stress at point A due to the axial load. Given, Axial load = 2 kN…

Q: Determine (a) the magnitude of the counterweight W for which the maximum absolute value of the…

A: Given data : Introduction : 1 - According to the problem we have to determine Magnitude of…

Q: 4. Draw the NA and stress diagrams (da, a.. a.) for the case given below.

A: As shown in the figure the position of compressive load is at the corner of the section so as there…

Q: Determine the maximum normal stress on a transverse plane in the straight portion of the structure…

Q: *1-32. Determine the largest intensity w of the uniform can be applied to the frame without causing…

Q: Question 2) In the system given in the figure, a distributed load of w=76 kN/m acts on the rod AB of…

Q: The cast iron beam in the figure has an overhang of length b = 2 m at each end. The bending working…

A: The given data is: σt=20 MPaσc=80 MPaσa=2 MPa

Q: Why is the force Fd pointing downwards? By force equilibrium, shouldnt it be 3 + Fd = 9 Fd =…

A: yes, you are right by equalibrium condition 3+Fd=9 we calculate reactions using the equailibrium…

Q: Question 2) In the system given in the figure, a distributed load of w=85 kN/m acts on the rod AB of…

Q: The force P is applied at d = 50 mm from the bottom as shown. Compute the normal stress at section…

A: Given: The value of d is 50 mm. The value of P is 85 kN. Consider the figure,

Q: Q1). Determine the maximum stress produced by the loads and create the shear and moment diagram.

A: ∑MA = 0 = - By×10 + 200×4×2By = 160010 = 160 N∑FY = 0Ay + By = 200×4Ay = 800 -160 Ay = 640 N∑FX = 0…

Q: Given: Maximum positive shear = 3960 N Maximum negative shear = 5640 N Maximum positive moment =…

Q: Member AC is subjected to a vertical force of 3 kN. Cross sectional area of tie rod is 400 mm? and…

Q: me beam shown ists of a 200 GPa; /= 1120 × 106 mm4]. If w= 66 kN/m and P= 128 kN, determine: AY, V P…

A: The beam shown in Figure Q.2 consists of a W610 × 140 structural steel wide-flange shape [E = 200…

Q: The lap joint is connected by three 40-mm-diameter rivets. Assuming that the axial load P= 70 kN is…

Q: 300 mm 30 kN/m 50 mm 40 kN c 50 mm A 350 mm 4 m 2 m 2 m 50 mm 200 mm a. Draw the shear diagram of…

A: Hi! Thank you for the question As per the honour code, We’ll answer the first question since the…

Q: The force P is applied at d = 50 mm from the bottom as shown. Compute the normal stress at section…

Q: The beam ABCD with a cross section carries the loading shown in the figure. Determine the magnitude…

A: Find:Magnitude and location of maximum bending stress in the beam

Q: The given figure(all dimension are in mm) shows an thin T section of beam. 100 mm . P • 10 <--20 num…

A: Given- T section of the beam as shown- Shear stress at Q=?

Q: Determine the normal stress at A and B in member CD. Pins C and D are at the centroid of the T secti…

Q: The T section shown in Fig. is the cross-section of a beam formed by joining two rectangular pieces…

A: Given : Max. shearing force in beam = 60kN This is a problem of solid mechanics where we are asked…

Q: Q.3) A simply supported wide-flange (see figure below) beam of span length L carries a vertical…

A: Given : Section : W 10 X 30 L = 8.5 ft P = 5 kips Alpha = 26.57 degrees We are asked to determine…

Q: 4. A force Q is applied to a rectangular member with a size of 3oomm x 450mm. Q is located 37.5mm…

A: Applying Bending stress and Direct stress concept Q load is applied with ecentricity on both axis…

Q: SITUATION. A square post is made up of two parts glued at an angle of 30 from the vertical axis.…

Q: A force P of magnitude 1,100 N is applied to the pedal shown satisfies a shearing stress in the pin…

A: Applied force P = 1100 N Shear Stress in the pin = 42 MPa We have to determine the followings:…

Q: The internal shear force V at a certain section of an aluminum beam is 10.2 kN. If the beam has the…

A: Given Data Width of flange = 69mm thickness of flange = 4mm Depth of beam = 72 mm Height of web =…

Q: Note : Answer all the Questions Q/ The below cross section is for a beam has a maximum applied…

Concept explainers

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.

Question

a. Determine the value of bending stress if the max value of moment is 702 kN.cm b. Determine the value of shear stress if the max value of shear is 420 kN.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the location of the shear center for the following section. Determine the shear stress at point A, if a 20 kN (downwards) shear load is applied at the shear center. Given: h1 = 25 mm h = 100 mm b = 50 mm Thickness = 4 mm. V ke- A |▬▬b▬|| h₁
Determine the largest weight W that can be supported by the two wires AB and AC. The working stresses are 14.5 ksi for AB and 21.8 ksi for AC. The cross-sectional areas of AB and AC are 0.6 squares inches and 0.3 squares inches respectively. 30° A 45° W B.
Refer to the figure shown below, the hinged support at A is in double-shear connection while the support at B in single shear shear connection. Forces P is applied at C and F is an axial force produced from a member BD connected at B. Given data: x = 1.2 m, y = 1.5 m and z = 1.8 m. ∅ = 20 degrees. If the axial stress of BD is limited to 180 MPa, wherein BD is made of 50-mm square tubing with thickness is one-tenth of its dimension, which of the ff. most nearly gives the shearing stress of the 20- mm dia. pin at A in MPa.
. Problem 4: The lap joint is connected by 3 20mm - diameter rivets. Assuming that theload P = 50 KN is equally distributed among the 3 rivets, find-The shear stress in each rivet. - The bearing stress between rivet and plate. - The tensile stress in each plate.
1. We have a truss structure with a hinge on the left and a roller on the right. (Use method of moments ONLY for finding the members and use the numbered name only for each member) 30.00" a) Find the force acting on members 2, 3, 7, 9, 14, 15. (Indicate Compression or Tension) b) Determine the normal stress @ members 2, 3, 7, 9. (Use figure 2 for cross-sectional area) P/2 30.00" T IP 30.00" T Figure 1 30.00" P/2 30.00" P/2 10.00" 20.00" 2.00" 0.20" Figure 2 0.20" 2.00" 0.20"!
1. We have a truss structure with a hinge on the left and a roller on the right. (Use method of moments ONLY for finding the members and use the numbered name only for each member) 30.00" a) Find the force acting on members 2, 3, 7, 9, 14, 15. (Indicate Compression or Tension) b) Determine the normal stress @ members 2, 3, 7, 9. (Use figure 2 for cross-sectional area) P/2 30.00" D foo 30.00" Figure 1 30.00" (10 N -30.00" P/2 P/2 10.00" 20.00" 2.00" 0.20" Figure 2 0.20" 2.00" 0.20"
i need the answer quickly
A square bar carries a series of loads as shown in Figure P1-47. Compute the stress in each segment of the bar. All loads act along the central axis of 1-47. the bar.
Q.2 A force F is applied to a rigid beam AB. The diameter of the deformable 2х X post AC is 20 mm and diameter of the deformable post BD is 10 mm. A B F= 60 (kN) and x = 1.2 (m) E=70 GPa for the posts AC and BD. 1m 1m C Calculate the followings a) Normal stresses at post AC and BD b) Normal strains at post AC and BD c) Deformations at post AC and BD d) Angle of tilt that occurs in Beam AB.
9. A single horizontal force P of magnitude 900N is applied to end D of lever ABD shown in the figure below. Knowing that portion AB of the lever has a diameter 36mm, determine a) the normal and shearing stresses on an element located at point H and having sides parallel to the x and y axes, b) the principal planes and the principal stresses at point H. 300 mm 120 mm y B H A 540 mm 36 mm P D
Determine the maximum normal and shear stresses
lute flexural stress. For the beam shown in Figure (3), given INA = 1.+ 10 mm", calculate the transverse shearing stress at points A, C and G on the section at the left support of the beam.