Member AC is subjected to a vertical force of 3 kN. Cross sectional area of tie rod is 400 mm? and the contact area at C is 650 mm2. o Determine the force in the tie rod if the average compressive stress at C is equal to the average tensile stress in the tie rod АB. ® Determine the compressive force at C. O Determine the position x of the 3 kN force from A. B. 3 kN C 200 mm

Member AC is subjected to a vertical force of 3 kN. Cross sectional area of tie rod is 400 mm? and the contact area at C is 650 mm2. o Determine the force in the tie rod if the average compressive stress at C is equal to the average tensile stress in the tie rod АB. ® Determine the compressive force at C. O Determine the position x of the 3 kN force from A. B. 3 kN C 200 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Construct the Mohr's circle for a point in the machine member subjected to pure shear of 50 MPa. Determine the maximum and the minimum stresses induced and orientation of their planes.
Question 5 Match the answers in the columns. v Maximum Shear stress of a cross section. A. using an l-section instead of a rectangular section. v Maximum Bending stress of a cross section. B. Tension and bending force. C. 1m form the supports - v If a simply supported beam is subjected to a distributed load, where are you most likely to find tension bending cracks. D. At Midspan - v Ifa simply supported beam is subjected to a distributed load, where are you most likely to find shear cracks. E. Midspan at the bottom v The bending stress in a section can be reduced by using a F. Midspan at the top v Shear stress can be increased by the width of a section. G. At the supports. v The shear force in fasteners. H. Reducing the width of a section. v Moment couple on a section. 1. using a rectangular section instead of an l-section J. Shear flow K. Increasing the width of a section. L. Only at the section sides touching the NA M. In between the NA and the top/bottom fibres N. Usually at the NA…
If the applied load "P" causes the point C to be displaced downward by &c=1 mm, determine the normal strain in members AC and BC. The unloaded lengths are LAC-210 mm and LBC=480 mm. A The strain for link AC is The strain for link BC is 60° 45° Submit Question O Is Question Help: Message instructor SC B
2. The major and minor principal stresses at the point are 3 MPa and -3 MPa respectively. The maximum shear stress at the point is (A) Zero (C) 6 MPa (B) 3 MPa (D) 9 MPa
A truss system is supported by two pins at the top. Determine the absolute value of the axial stress in member AC (in MPa) if the diameter of the member is 30 mm. Sm 36 AN 4m 2m Go kN
6
0.15
Consider the loads of the figure to be axially applied at sections B, C, and D to the concrete structure supported at A. IW E F P G 5 kN 5 kN A Determine P in kN when member BC is 24 mm in diameter, the axial stress in section F is 588 MPa, and W 309822 N. = 10 kN C 10 kN Rigid -bearing plates
For the beam and loading shown, for section n-n (y = 75mm (from base), I = 79.688 x 106 mm) determine (1) the largest shearing stress in section n-n. (2) the shearing stress at a in section n-n. (3) the shearing stress at b in section n-n. (4) the shearing stress at d in section n-n. (d is on the flange) (5) the shearing stress at d in section n-n. (d is on the web) 200 KN 200 KN 122 0.75 m 1.2 m 0.75 m B 50 mm 50 mm -G b .d 14 75 mm 75 mm 75 mm 150 mm 50 mm
Q4: determine the maximum tensile and compressive stresses acting normal to the beam. 50 mm 10 kN 100 mm 30 kN 6 m 2m B (2
The solid 1.85-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 925 lb/ft. Two concentrated loads also act on the rod: P= 1700 lb and Q = 1100 lb. Assume a = 20 in. and b = 40 in. Determine the normal stress in the rod at the following locations: (a) x = 13 in. (b) x = 39 in. > > > -> -> > b Answer: Ox=13in. = psi Ox=39in. = psi
2. Two 115-mm wide by 15-mm thick steel plates are welded as shown. The load P = 135 kN is concentrically applied and B= 25°. For the xy directions shown, determine a) b) The normal stress or acting perpendicular to the weld; The shear stress try' acting parallel to the weld; Sketch the state of stress to represent results from a) and b) above. В P 2² 115 mm. P