Answered: 2. The major and minor principal…

2. The major and minor principal stresses at the point are 3 MPa and -3 MPa respectively The maximum shear stress at the point is (A) Zero (C) 6 MPa (B) 3 MPa (D) 9 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Cylinder of height 2H. radius R. centroid at (0,0.H), axis e3 undergoes deformation x = o(z) = z + 23e3. Assuming stress-strain relation: S = aE, where a is a constant, total force on the base of the cylinder with normal -e3 is f = -1.5anR2 He3 total force on the base of the cylinder with normal - ez is f = 1.5aπR²e3 total force on the base of the cylinder with normal - ez is f = 1.5an R²Hez total force on the base of the cylinder with normal - ez is f = -1.5anR²e3
The major and minor principal stresses at a point are 3MPa and -3MPa respectively. The maximum shear stress at the point is
0.13
Determine the absolute maximum shear stress for each of the following plane stress states for which the principal stresses are given. (a) оp1 — 3940 рsi, Op2 -1980 psi, o p3 D0 (b) op1 = 83 MPa, o,2 = 60 MPa, O,3 = 0 Answer: (a) Tabs max psi = (b) Tabs max= MPa
All forces applied in the system are in the (x - y) plane. The material point B at the top of the beam is rotated at an angle of 15° counterclockwise. It is required that the shear stress is 17.5 MPa for this rotated material point B. At the bottom point A of the beam it is required that the maximum tensile stress is 110 MPa. Determine the load P and the length d that satisfies these constraints defined for points A and B. Given data: L= 4 b, t = b / 25, c = 2b, b = 1000 mm, e = 12, f=5 b/4- q = 2P/L b/ 4 -b/4- P
2. The major and minor principal stresses at the point are 3 MPa and -3 MPa respectively. The maximum shear stress at the point is (A) Zero (C) 6 MPa (B) 3 MPa (D) 9 MPa
A rigid bar AB is hinged at A and supported by copper rod 2 m long and steel rod i m long as shown in fig. the bar carries a load of 20 KN at B. the cross section areas of steel and copper are 200 mm2 and 400 mm2 respectively find the stress in each rod ?if Es=210 GPa and Ec=83 GPa Copper rod 2m Steel rod- -1 m- 1m 2 m m- B 20 KN
For the beam and loading shown, consider the n-n cross section. (a) the absolute value of |M| of the bending moment in the n-n section N.m (b) determine the absolute value of the normal stress in the direction of the X axis at point A of the n-n section |σx| MPa in units, c) determine the absolute value of the maximum shear stress at Point A of the n-n section |tmaks| MPa in units. The inside of the beam is full and the cross-section measures are as shown in the figure. Supports only support vertical forces. Take P1 in the question for 220 N and P2 for 323 N. Point A is at the bottom of the beam.
g44. The tapered member is fixed connected at its ends A and Band is subjected to a load P.Determine the location x of the load and its greatest magnitude so that the average normal stress in the har does not exceed oa = 28 MPa. The member is 50 mm thick. 150 - 1500 mm
Q.17 The maximum bending stress is A - w/m L P Od
Problem 2. [Concepts: Internal forces in 2D and average normal stress] The bars of the truss each have a cross-sectional area of 1.25 in². a) Determine the average normal stress in each member due to the loading P = 8 kip. State whether the stress is tensile or compressive. b) If the maximum average normal stress in any bar is not to exceed 20 ksi, determine the maximum magnitude P of the loads that can be applied to the truss. 4 ft 4 ft 4 E 0.75 P 0
Find the mayximum bending stress 75 N/m 60° N/m 2) 5m Ø Icm