For the beam and loading shown, for section n-n (y = 75mm (from base), 1 = 79.688 x 106 mm) determine (1) the largest shearing stress in section n-n. (2) the shearing stress at a in section n-n. (3) the shearing stress at b in section n-n. (4) the shearing stress at d in section n-n. (d is on the flange) (5) the shearing stress at d in section n-n. (d is on the web) 200 kN 200 KN 122 0.75 m 1.2 m 0.75 m B 50 mm 50 mm -G b .d 14 75 mm 75 mm 75 mm 150 mm 50 mm

For the beam and loading shown, for section n-n (y = 75mm (from base), 1 = 79.688 x 106 mm) determine (1) the largest shearing stress in section n-n. (2) the shearing stress at a in section n-n. (3) the shearing stress at b in section n-n. (4) the shearing stress at d in section n-n. (d is on the flange) (5) the shearing stress at d in section n-n. (d is on the web) 200 kN 200 KN 122 0.75 m 1.2 m 0.75 m B 50 mm 50 mm -G b .d 14 75 mm 75 mm 75 mm 150 mm 50 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

Q: Problem Sets - 3: The cast iron inverted T-section supports two concentrated loads of magnitude P as…

Q: 24. A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm…

Q: Problem 3 in the steel structure shown, a 6-mm-diamter pin is used at D and 10-mm-diameter pins are…

Q: Two plates are joined by four bolts of d=20-mm diameter, as shown in the figure. The shearing stress…

A: We have to determine the value of maximum load P as the shearing stress is limited to 70 MPa,…

Q: 3. The tension member is fastened together using a single bolt as shown. The bolt has a diameter of…

A: Given : Dia of bolt = 0.6 in. Allowable shear stress for bolts = 8ksi Allowable average normal…

Q: In the steel structure shown (see Figure Q1), a 6-mm-diameter pin is used at B and C and

A: According to given data

Q: Vertical load is applied to point B of a 10 mm radius cylindrical bar as shown in the figure.…

Q: Problem # 3: The strut AB made from two bars (thickness of each bar = 0.50 in) is connected to a…

Q: The solid aluminum shaft has a diameter of 50 mm and an allowable shear stress of Tallow =60 MPa.…

Q: 20MPA a In Figure , according to the stress condition of a stack of I-section beam. (30Mpa is the…

A: Principal stress=σx+σy2±σx-σy22+ζ2=40+-202±40-(-20)22+302=10±42.42 MpaThus σp1=52.42Mpa and…

Q: Determine the largest permissible value of P for the beam and loading shown, knowing that the…

Q: COMPUTE THE SHEARING STRESS IN THE PIN AT B FOR THE MEMBER SUPPORTED AS SHOWN IN THE FIGURE. THE PIN…

Q: F1 (kN) 80 mm 30 mm 80 mm F2 (kN) 30° 400 mm The system is loaded with F1 (100) and F2 (200) as…

A: Note - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: 4 in 7/8 in 7/8 in 2. The lap joint shown in the figure, is fastened by four 25mm.-diameter rivets.…

Q: A steel shaft is loaded as shown. Knowing that T₁ = 1000 N.m, T₂ = 1600 N.m, L=250 mm, d 40 mm, D =…

A: Given: T1 = 1000N .m T2 =1600 N.m, L = 250mm , d =40 mm, D = 45mm Required : Maximum shear stress…

Q: R14-9. The 60 strain ronette is mounted on a beam. The following readings are obtained for each…

A: Given: The 60 strain rosette is mounted on a beam. The following readings are obtained for each…

Q: 3) Find a) the maximum stress in the shown member, b) the relative displacement between 8 and D (Ap)…

Q: Q4 - For the given beam and cross section, at point B on section A-A (mid-span), determine the…

Q: O If P = 52.2 kN, determine (a) the factor of safety (F.S.) for the average shear stress in pin A…

Q: The outer diameter of the bronze pipe flush-mounted at the A and B points is given as D and the wall…

Q: The safety stress for the steel bar shown in the figure is σallow= 160MPa. According to the greatest…

A: Solution:

Q: What is the Maximum Shear Stress, t, on the centric axially loaded member shown? The cross-sectional…

A: Given data : Axial load (P)=40 kipsCross sectional area (A)=2 in2

Q: Problem 2 (for all students). Determine the state of stress, the principal stress and the max in-…

A: Calculating the moment of inertia: IP=π32504-404 The torque will be:T=6×300=1800 KN-mmThe bending…

Q: cmonl *9-56. The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and…

Q: 40KN The beam, having the cross-section «I», is 60kNm subjected to a loading as shown in the figure.…

A: Any Beam or structure under the application of loading shows the bending deformations due to that…

Q: Knowing that a force P of magnitude 1000 N is applied to the pedal shown, determine (a) the diameter…

Q: Determine the principal stress and absolute maximum shear stress developed at point B on the cross…

Q: In the following structure, consider the following data: The connection at D is double and has a…

Q: Question 3 A compressive force of 45 kN acts parallel to the longitudinal axis of the I-section as…

Q: The truss shown consists of wooden members. Knowing that each member has a 50 x 50 mm. square cross-…

Q: the AC rod suspended. The cross section of the AC rod is 15 x 8 mm2. 1.6 tons of force is applied to…

Q: For the beam below find the normal stress at sections in point (B) and (C) 75 kN 35 kN 45 kN 85kN…

A: T oFind :- normal stress at B and C in sections of the beam

Q: QI: Find the normal stresses at sections A-A, B-B, C-C, and, D-D for the body as shown in figure…

Q: Determine the spacing of rivets in mm. Determine the maximum flexural stress at 1 m from the support…

A: Given: τ=100 Mpa σb=220 MPa bearing stress for single shear rivet σb=280 MPa bearing stress for…

Q: HWAA traingular beam Beomm wide by 30omm height is Pinned at A, SuPPorted by a able CD ad Carries a…

Concept explainers

Planar Stresses

Question

For the beam and loading shown,
for section n-n (y = 75mm (from base), I = 79.688 x 106 mm) determine
(1) the largest shearing stress in section n-n.
(2) the shearing stress at a in section n-n.
(3) the shearing stress at b in section n-n.
(4) the shearing stress at d in section n-n. (d is on the flange)
(5) the shearing stress at d in section n-n. (d is on the web)
200 KN 200 KN
122
0.75 m 1.2 m 0.75 m
B
50 mm
50 mm
-G
b
.d
14
75 mm 75 mm 75 mm
150 mm
50 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider the truss structure and the loading given below. a) Compute the average axial stress on member AB, b) compute the average shear stress at the pin of connection A. d- 20 mm 600 mm 50 mm -S00 mm 60 kN 25 mm | I 20 mm 30 mm I20 mm 25 mm TOP VIEW OF MEMBER AB d = 30 mm
Assume that 4-18mm diameter rivets join the plates that are each 120mm wide. The allowable stresses are 120MPa for bearing in the plate material and 60MPa for shearing of rivets. Determine the following:a. The minimum thickness of each plateb. The largest average tensile stress in the plate F=70
9-6. Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem using the method of equilibrium described in Sec. 9.1. 9-7. Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem using the stress transformation equations. Show the result on the sectioned element. 45 MPa 45° Probs. 9-6/7 80 MPa
show complete solution
Determine the number of main bars, spacing, and determine the spacing for stirrups.
0.16
The five 20mm-diameter rivets fasten the plate as shown in the figure to the fixed member. a). Determine the value of the load P so that the average stress of any rivet does not exceed 80MPa.b). What additional clockwise torque can be applied before the shearing stress exceeds 90MPa
The assembly shown below is pinned at A & C and A & C are subjected to a double shear. Let each pin diameter be 18 mm, and P = 20 kN. Find the:a) Force at the rod BC (kN) and force acting on pin A (kN)b) Average shear stress at A (MPa), and average shear stress at C (MPa)
The shown L-shape cantilver is loaded as shown and fixed at A. It has a constant section of 40 mm X 20 mm. For point I located at 50 mm from support A, at the midheight of the section, determine the principal stresses, the principal planes and the maximum shear stress. y 50 mm 150 mm 40 mm 0.5 kN H- I 20 mm 3 kN 160 mm 2.5 kN
#2 will upvote anyone who will answer
The load on the bearing of cast iron bracket is 5 kN. The cross section at section AB is given. Calculate the greatest tensile stress across the section AB and the distance of the neutral axis of the section from the centriod of the section. 10cm 5 KN A B 10cm 1.25cm 7.5cm
3. For the beam with cross-section shown: a. Determine the maximum tensile stress, and indicate which points experience this stress (tell which cross-section feels this stress, and which points on that cross-section feel this stress). b. Determine the maximum compressive stress, and indicate which points experience this stress (tell which cross-section feels this stress, and which points on that cross-section feel this stress). c. Determine the maximum shear stress, and indicate which points experience this stress (tell which cross-section feels this stress, and which points on that cross-section feel this stress). d. For the cross-section 2 m to the right of A, determine the normal stress at point D on the cross-section, and state whether this stress is tensile or 100 KN m compressive. e. For the cross-section 2 m to the right of A, determine the shear stress at point D on the cross- section. f. Determine the equations for the elastic curve, and for the slope of the elastic curve, for…