The steel pipe AB has a 64-mm outer diameter and a 5-mm wall thickness. Knowing that arm CDE is rigidly attached to the pipe, determine the principal stresses and the maximum shearing stress at point K. 120 mm 3 kN 120 mm 19 kN 150 mm

Q: L. 125 МPа 62.5 MPa- 62.5 MPa 125 MPa

A:

Q: Problem: Determine the maximum shearing stress developed in each material. Also, determine the…

A:

Q: For the below shaft, knowing that T= 36 kip.in, The modulus of rigidity for the Steel and the…

A: It is parallel combination of shaft, so there is no relative motion between them. Angle of twist in…

Q: 2. The major and minor principal stresses at the point are 3 MPa and -3 MPa respectively The maximum…

A: To find out the maximum shear stress at the point.

Q: 6. W = 50 kN/m 100 mm 100mm W = 40 kN/m 150 mm fc = 40 MPa 8 m 2- 20mm Ø ww oz ww 08

A: Unlike prestressed concrete, post-tensioned concrete has tendons which are tensioned after the…

Q: 24. A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm…

A:

Q: Q.17 The maximum bending stress is 0039 A w/m m L P Od

A:

Q: 200 MPa 500 MPa 350 MPa

A: Please refer the attached image for complete solution. THANK YOU.

Q: 1.0 m 3.3 m A simple pin-connected truss is loaded and supported as shown. All members of the truss…

A:

Q: A B 400 mm 500 mm 20 mm 40 mm 7 kN/m 3 m 20 kNm 2.5 m 2.5 m 2 m 15 KN A T-beam with the…

A: Given Data Determine  a. Second moment of area of cross section.  b. Draw the SFD and BMD.  c.…

Q: 4 KN 2m SKN> C 1.5 A

A:

Q: A builtup steel beam comprise of two flange plates 250 mm wide × 10 mm thick and web plate 330 mm…

A:

Q: Two pieces of lumber having square section (b x b) are arranged and supported as shown. The…

A:

Q: A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is…

A:

Q: Determine principal stress

A: Given  Normal stress X = -10MPa Normal Stress Y = -3 MPa Shear stress = -2MPa   To find Principal…

Q: The solid aluminum shaft has a diameter of 50 mm and an allowable shear stress of Tallow - 6 MPa.…

A: Given data,  Radius of shaft (r) = 25 mm Allowable shear stress = 6 MPa

Q: The copper pipe has outer and inner diameters of 2.5 in and 2.0 in. If it is tightly secured to the…

A:

Q: Hinge

A:

Q: -57. Determine the principal stress, the maximum in-plane shear stress, and ver 120 MPa MADARAKAN…

A: Given data : The value of normal stress in X direction σX=300 MPa The value of normal stress in Y…

Q: (d) Radius of Mohr's circle (e) maximum value of the principal stress omax at the junction of the…

A: Question is based on the simply supported beam subjected to concentrated load at center. Properties…

Q: Find maximum principal stress

A: Given data : The value of normal stress in X direction σX=-30 MPa The value of normal stress in Y…

Q: Link AB is to be made of a steel for 15 kN/m which the ultimate normal stress is 30° 400 MPa.…

A:

Q: A rectangular cantiliver wooden beam is applied by point load of 400in at free end  Determine cross…

A: Direct stress: Stresses that act normally in relation to the plane of the object are referred to as…

Q: F1 (kN) 80 mm 30 mm 80 mm F2 (kN) 30° 400 mm The system is loaded with F1 (100) and F2 (200) as…

A: Note - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: 1. From the given truss below, answer the following: 9 m G 4 m 135 kN 135 kN B 4 m C4m E Compute the…

A:

Q: A shaft composed of segments AC, CD, and DB is fastened to rigid supports and loaded as shown in…

A:

Q: diameter of the smallest pin that can be used if not to exceed a shear stress of 60 MPa (Draw

A:

Q: Assume that 4-18mm diameter rivets join the plates that are each 120mm wide. The allowable stresses…

A:

Q: Member AC is subjected to a vertical force of 3 kN. Cross sectional area of tie rod is 400 mm? and…

A:

Q: Q.17 The maximum bending stress is 0039 A w/m m L P Od

A:

Q: Q.17 The maximum bending stress is A w/m L P Ond

A:

Q: Determine the maximum shearing stress developed in each segment. For bronze, G = 36 GPa; aluminum, G…

A:

Q: 400 kN -0.5 m- -0.5 m A B 0.4 m D E F

A:

Q: Determine the principal stress and absolute maximum shear stress developed at point B on the cross…

A:

Q: In the following structure, consider the following data: The connection at D is double and has a…

A:

Q: The drill pipe has an outer diameter of 3 in., a wall thickness of 0.25 in., and a weight of 50…

A: For the given drill pipe,

Q: 40 MPa 35 MPa 60 MPa

A:

Q: PROBLEM 2 Strips A and B are to be glued together using the two strips C and D. a. Determine the…

A: force transfered by C strip = Force in D strip=force in A strip 2=20 KNlet the width of the strip C…

Q: Question 3. The steel shaft has a diameter of 40 mm and is fixed at its ends A and B. If it is…

A: Given data: LAC=400 mm LCB=600 mm diameter= 40 mm G=75 GPa.

Q: The center post B of the assembly has an original length of 124.7 mm, whereas posts A and C have a…

A:

Q: Match the answers in the columns. v Maximum Shear stress of a cross section. A. using an l-section…

A: Given data  Shear stress Bending stress Simply supported beam  Moment couple

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.