Determine the maximum normal stress on a transverse plane in the straight portion of the structure shown below and clearly indicate where it occurs. The member is braced in the plane perpendicular to the plane of symmetry. Consider: (a) Section B-B shown below at the left (symmetric section). (b) Section B-B shown below (unsymmetric).

Determine the maximum normal stress on a transverse plane in the straight portion of the structure shown below and clearly indicate where it occurs. The member is braced in the plane perpendicular to the plane of symmetry. Consider: (a) Section B-B shown below at the left (symmetric section). (b) Section B-B shown below (unsymmetric).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The two vertical steel [E = 200 GPa] rods that support rigid bar ABCD are initially free of stress. Rod (1) has an area of A₁ = 350 mm² and a length of L₁ = 2.1 m. Rod (2) has an area of A₂ = 375 mm² and a length of L₂ = 1.5 m. Assume dimensions of a = 3.2 m, b = 1.1 m, and c = 1.4 m. After a load of P = 130 kN is applied to the rigid bar at D, determine: (a) the normal stresses in rods (1) and (2) (b) the magnitude of the downward deflection of the rigid bar at D. y,v (2) a L2 Rigid bar L₁ Answer: (a) σ₁ = i 02= i (b) VD= i (1) B MPa MPa mm -X,U b C ↓ С D P
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 110 GPa] with a cross-sectional area of A₁ = 630 mm². Bar (2) is an aluminum alloy [E = 79 GPa] with a cross-sectional area of A₂ = 340 mm². A concentrated load of P = 52 kN acts on the structure at D. Assume L₁=910 mm., L₂=430 mm., a=450 mm., b=280 mm., and c=1030 mm. Determine: (a) the normal stresses 0₁, 02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. a 5 Answers: (a) 6₁ (b) VD= = tel i (1) L₁ L2 B C MPa, 0₂ = mm. i MPa
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 92 GPa] with a cross-sectional area of A₁ = 680 mm². Bar (2) is an aluminum alloy [E = 74 GPa] with a cross-sectional area of A₂ = 350 mm². A concentrated load of P = 56 kN acts on the structure at D. Assume L₁=900 mm., L2=600 mm., a=580 mm., b=310 mm., and c=1160 mm. Determine: (a) the normal stresses 01, 02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. b Answers: (a) o₁ = (b) VD= i i L₁ L2 (2) B C MPa, 0₂ = mm. i D MPa
7-3. For the given state of stress shown, determine: (a) the principal stress, and (b) the maximum in-plane shear stress and the associated average normal stress. Also, for each case, determine thecorresponding orientation of the element with respect to the element shown, and sketch the results oneach element.
The two vertical steel [E = 200 GPa] rods that support rigid bar ABCD are initially free of stress. Rod (1) has an area of A1 = 410 mm2 and a length of L1 = 3.2 m. Rod (2) has an area of A2 = 355 mm2 and a length of L2 = 1.3 m. Assume dimensions of a = 3.4 m, b = 1.2 m, and c = 1.5 m. After a load of P = 50 kN is applied to the rigid bar at D, determine: (a) the normal stresses in rods (1) and (2) (b) the magnitude of the downward deflection of the rigid bar at D. y,v (2) L2 a B C D x,u Rigid bar |(1) Answer: (a) o1 = i MPa 02 = i MPa (b) VD = i mm
9. Find the stresses in members BC and BE for the truss shown. The cross-sectional area of each member is 3780 mm². Indicate whether the stresses are tensile (T) or compressive (C). BC = 4.44 MPa (C), BE = 3.45 MPa (T) B C 50° 50° 50⁰° E 20 KN 50% D
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 109 GPa] with a cross-sectional area of A₁ = 530 mm². Bar (2) is an aluminum alloy [E = 64 GPa] with a cross-sectional area of A2 = 330 mm². A concentrated load of P = 67 kN acts on the structure at D. Assume L₁=740 mm., L₂=500 mm., a=660 mm., b=310 mm., and c=1030 mm. Determine: (a) the normal stresses 0₁, 02 in both bars (1) and (2). (b) the downward deflection VD of point D on the rigid bar.
For the steel truss (E=29 × 106 psi) and loading shown, determine the deformations of members AB and AD, knowing that their cross- sectional areas are 4.0 in2 and 2.8 in2, respectively. It is given that P= 50 kips. P A B 8 ft D C -13 ft- -13 ft- The deformation of member AB is - in. The deformation of member AD is in.
10. The rigid bar below is supported by axial bar (1) and by a pin connection at C. Axial bar (1) has a cross-sectional area of A₁ = 275 mm², an elastic modulus of E = 200 GPa, and a coefficient of thermal expansion of a = 11.9x 106/°C. The pin at C has a diameter of 30 mm. After load P has been applied and the temperature of the entire assembly has been increased by 31°C, the total strain in bar (1) is measured as 975 μe (elongation). Determine: (a) the magnitude of load P. (b) the shear stress in pin C. 275 mm Connection detail (1) Rigid bar 540 mm 135 mm 260 mm
A pin-jointed truss ABC shown below consists of two links AB and BC. These links are 6 mm thick and 20 mm wide as shown. There are support brackets at A and C. All pins are 12 mm in diameter and a vertical force, P = 9 kN is applied at pin B as shown. The angle 0 =38 deg. and the angle ẞ = 0 + 20 deg. The normal stress in link AB is (The result is accurate to one decimal place, in the unit MPa. Please write down only the value of your final result) · 12mm 9 20mm -1.0m⋅ B
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 116 GPa] with a cross-sectional area of A₁ = 550 mm². Bar (2) is an aluminum alloy [E = 71 GPa] with a cross-sectional area of A₂ = 290 mm². A concentrated load of P = 62 kN acts on the structure at D. Assume L₁=800 mm., L2=560 mm., a-590 mm., b=430 mm., and c=1160 mm. Determine: (a) the normal stresses 01, 02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. a b Answers: (a) σ₁ = (b) VD = i (1) L₁ L2 (2) A B MPa, 0₂ = mm. D MPa
Radius of the pin at C is 3mm. While at static equilibrium, we know that a force P of magnitude 500 N is applied to the pedal shown, calculate (a) The average shearing stress in the pin at C (b) the corresponding bearing stress in the pedal at C, (c) the corresponding bearing stress in each support bracket at C. 9 mm T 5 mm C A 75 mm 125 mm B 300 mm PI D