21 P3. 2) Determine the displacement of each member or E = 200 GPa %3D |P 650 kN %3D Diameter 1 = 25mm 1.0 m P= 850 kN %3D Diameter 2 = 35mm 1.25 m P = 1500 kN %3D 0.75 m Diameter 3 = 50mm

Q: I'd appreciate it if you could elaborate on what you mean by "GIS," thanks.

A: GIS stands for Geographic Information system and are computer-based tools that investigate…

Q: show the integration process

A: To show the integration process

Q: What is a pick

A: The term pick may be defined in various ways according to the situation Firstly Pick may defined as…

Q: I would appreciate it if you could explain what you mean when you say "GIS."

A:

Q: 4. Why the lines on the graph do not pass through the origin?

A: When any graph line does not pass through the origin, it means that when the input equals…

Q: What is Structural Plan?

A: A structural plan is a plan used as a framework to take up the land development or renovation of an…

Q: Environmental Effects of engineering constructions projects. Include photos.

A: Environmental engineering : Environmental engineering comprises the development of methods and…

Q: Why are Construction Photographs needed?

A: There are various reason for the Need of construction photograph some of them are mentioned here:

Q: What is the most common use of RFI?

A:

Q: Within the preceding elements,what should be the preference order for the documents?

A: An order of precedence is listed to resolve any disputes that arise from the conflicts between the…

Q: 10 25k 10'

A: The below cantilever beam is given;

Q: where did you get 6?

A: 6 is the loading intensity at B.

Q: What does the reductent diagram look like?

A: What does the reductent diagram look like?

Q: What do you mean by external substratum

A: The structure is divided into the 2-main subparts, by using the position of the build. Those are…

Q: The

A: The construction schedule normally contains sufficient detail to schedule the day to day work on a…

Q: what is ytm

A: There are different type of the calculation done in the funds. The funds can increase or decrease…

Q: what is america door panel and it size

A: Solution: The most common front sizes of the door in American houses are 36 inches wide and 80…

Q: What is Third Party Certification?

A: When an item or organisation has the formal verification or authentication of certain…

Q: 2 unsafe acts and unsafe conditions associated with ergonomics and psychological hazards in…

A: Solution- Electrocution, falls from large heights, damages from tools, equipment's, and machine,…

Q: How can outdated structures progress?

A: The given question has asked 'how can outdated structures progress'? Old Structures  Old structures…

Q: How significant is the alphabet of lines that interprets a drawing if drawing is stated to be the…

A: concept- Drawings show how an object will be made in a straightforward and correct manner. It…

Q: Explain the Modified Mercalli scale.

A: The effect caused on the surface of the earth due to an earthquake is known as the intensity of the…

Q: * To draw an arc angle between two intersecting lines Fillet O Block O Trim Chamfer O If we want to…

A:

Q: What are the steps involved in the construction of a control unit that employs vertical coding, and…

A: It has been asked in the question to determine the steps involved in the construction of a control…

Q: Explain what is project close out?

A: The term project closeout in construction is the last stage of a construction project and an…

Q: Is "Object-Oriented" a term that may be used without any problems? The creation of software that…

A: "Object-Oriented" is a widely accepted and established term in software development that refers to…

Q: You are appointed as an officer of Occupational Safety to investigate the incident happened during…

A: Officer of Occupational Safety is responsible for 1) Enforcing safety policies, 2) Conducting audits…

Q: What is vadose zone ?

A: Vadose zone or Unsaturated zone is the part of the earth that is above the fully saturated earth…

Q: How to identify if "cos" or "sin" is to be used?

A: If force makes angle with x-axis, cos component will be considered along x-axis and sin component…

Q: What is the difference between primary standards  and secondary standards in AAQS?

A: Primary standards:These standards for the air pollution control considered the public health…

Q: Define the Principles of Limit States Design ?

A: we mainly designed structures for considering life span of any structures, within that life span of…

Q: Discuss how volume studies are being conducted

A: Traffic volume studies are conducted to determine the effectiveness of traffic control…

Q: HI, KINDLY IDENTIFY WHERE IS THE ANSWER FOR LETTERS A TO G.

A:

Q: Can you please solve the number 2 question in the picture? Thank you

A:

Q: Discuss Construction Methods

A: The various methods used in the construction industry with specific design and planning so as to…

Q: Define each term in three sentences only. 4. Curve Resistance 5. Air Resistance 6. What is AASHTO?…

A: (4.) Curve Resistance - * It is the loss of tractive force when a rear wheel     driven vehicle…

Q: Using specific examples (at least 5), discuss why you will prefer using CAD software for your…

A: A technical drawing used to convey information about an object is known as an engineering drawing. A…

Q: How did you get the "h" values

A:

Q: Can you please redo this and explain how you got what you got? I dont understand concept and show…

A: To draw a cross-section AA' and BB' for the given section.

Q: What is sandf

A: SANDF stands for South African National Defence Force.

Q: Briefly explain the purpose of a building code.

A: The main purpose of building codes are to provide minimum standards to safe life, health, property,…

Q: What critical elements are important to support the planning  process? In detail.

A: The clear goals, scenario analysis, stakeholder involvement, resource distribution, risk management,…

Q: What are the possible Geometric Design? Make a table Containing the Geometric Design and Design…

A: Geometric design is the process of determining the layout and dimensions of visible features of a…